Brake Servo Sealing Grommet? - Brake Repair Help


	Auto Repair Home	SEARCH POSTS	WHO'S ONLINE	LOG IN

Automotive Repair

Car Troubleshooting Topics
  Car Troubleshooting
  Engine Troubleshooting
  Engine Fault Codes
  Electrical and Wiring
  Transmission Problems

Car Repair Topics
  Car Making Noises
  Car Stereo Repair
  Heating or AC Issues
  Motorcycles and ATVs
  Tricks of the Trade
  Truck Repair Advice

Site Options:
  Login
  Sign up here!

Latest Forum Post

Lukewarm Heat............

New antifreeze reverse flush heater core...

multiple warning lights

2013 GMC Terrain 130,000 miles 4 cylinde...

2014 Nissan Sentra Shaking

Car recently started shaking when accele...

Buy Flualprazolam Powder Online Whatsapp: +1(424) 328-1086

N/A

1989 toyota pickup 3.0 crank no start

I have a 1989 toyota pickup 3.0 crank no...

Strut spring orientation and strut mount tension nut

2017 Nissan rogue awd 2.5 L Put in Monro...

Transmission stuck in part, I have tried everything

So I'm working on my elderly fathers 201...

2017 dodge journey LED headlights on/off randomly

Year of vehicle 2017 Make of vehicle dod...

Kia Soul starter replacement issues!

Okay so my car is a 2010 Kia soul 2.0 en...

Please Help - Knock sound & engine fail

Hi all, Hoping to get some insight and ...

Brake Servo Sealing Grommet?

Sign up here!

Search for (search options)

Auto Repair Home>> Automotive Repair>> Brake Repair Help

bangerclanger
New User

Apr 26, 2014, 12:26 AM

Post #1 of 4 (2042 views)

Brake Servo Sealing Grommet?	Sign In

Skoda Octavia Ambiente Estate TDI 1.9 approx 110.00 miles

My brake servo stopped working because the sealing grommet that sits in the bulkhead corroded and stopped being a seal. It is where the servo pipe meets the bulkhead and the grommet sits in the hole in the bulkhead so that the pipe can sit comfortably in it. Does anybody know if the grommet can be purchased as a part on its own or does the entire pipe need to be purchased? It is a Bosch part and the only identifying numbers on it are MR 67 and EPDM. If this part can be found, where on earth could I find it? Any help would be much appreciated.

Best wishes

Bangerclanger

Tom Greenleaf
Ultimate Carjunky / Moderator
Tom Greenleaf profile image

Apr 26, 2014, 12:51 AM

Post #2 of 4 (2035 views)

Re: Brake Servo Sealing Grommet?	Sign In

US based site so doing some guessing.

Servo: You mean what we call a "master cylinder" I think?
Bulkhead: You mean the "firewall" end of that cylinder - right?
If leaking brake fluid there you toss the whole unit for new not just some seal by all chances the basic design is similar to all vehicles and bleed system properly,

T

Discretesignals
Ultimate Carjunky / Moderator
Discretesignals profile image

Apr 26, 2014, 3:41 AM

Post #3 of 4 (2023 views)

Re: Brake Servo Sealing Grommet?	Sign In

I'm wondering if the OP means brake booster or vacuum servo? You could probably make a seal to go between the firewall and where the booster connects out of rubber or gasket material. The only thing it should be sealed for is to keep water out of the cabin.

Since we volunteer our time and knowledge, we ask for you to please follow up when a problem is resolved.

(This post was edited by Discretesignals on Apr 26, 2014, 3:42 AM)

Tom Greenleaf
Ultimate Carjunky / Moderator
Tom Greenleaf profile image

Apr 26, 2014, 5:19 AM

Post #4 of 4 (2019 views)

Re: Brake Servo Sealing Grommet?	Sign In

I should know the right terms DS. OP (original poster) if this lost vacuum assist is one problem or if brake fluid loss another. That rubber grommet to booster where a check valve goes might be sold separately but if the booster is corroded you should want a whole new one.

Need some clarification on just what your problem is. High chances this is vacuum assisted power brakes. If you can post a picture of the parts it would help. I don't know how to look up parts for this car from here,

T

Search for (options) Privacy Sitemap