|
|
greasy one
User
Sep 7, 2012, 12:35 PM
Post #1 of 13
(2602 views)
|
Hi noob here. I have 2 cars and I guess I am lucky that I have avoided a car forum, till now. By now, you prob. know that CV needs replace. New one is in back seat. I can't remember, for sure, ever replacing CV joints, but I was mechanic in 70's and early 80's. I have tools but no dead blow hammer. The box says something about that. Can I get a link to changing this? I didn't even waste time trying to google it, I just signed up on the first car forum on google. Car is '95 Subaru Leg. Breighten, left side, for now. Thanks and I will stick around if allowed to 
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Sep 7, 2012, 1:28 PM
Post #2 of 13
(2571 views)
|
|
Re: Ticking Subaru
|
Sign In
|
|
You're going to need a very big prybar to pop it out of the transmission.
FRONT DRIVE SHAFT
1) Disconnect ground cable from battery. 2) Jack-up vehicle, support it with safety stands (rigid racks), and remove front wheel cap and wheels. 3) Unlock axle nut. 4) While depressing brake pedal, remove axle nut using a socket wrench.
CAUTION: Be sure to loosen and retighten axle nut after removing wheel from vehicle. Failure to follow this rule may damage wheel bearings.
5) Disconnect stabilizer link from transverse link. 6) Disconnect transverse link from housing. 7) Remove spring pin which secures transmission spindle to DOJ.
CAUTION: Use a new spring pin.
8) Remove front drive shaft assembly. If it is hard to remove, use ST1 and ST2.
ST1 926470000 AXLE SHAFT PULLER
ST2 927140000 PLATE
CAUTION:
- Be careful not to damage oil seal lip when removing front drive shaft.
- When front drive shaft is to be replaced, also replace inner oil seal.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
greasy one
User
Sep 7, 2012, 6:31 PM
Post #3 of 13
(2538 views)
|
|
Re: Ticking Subaru
|
Sign In
|
|
I am having second thoughts about this. Maybe start with getting a pry bar
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Sep 7, 2012, 6:34 PM
Post #4 of 13
(2534 views)
|
|
Re: Ticking Subaru
|
Sign In
|
|
You're also going to need a real heavy duty socket and impact gun for the axle nut that is over 150 Ft lbs.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
(This post was edited by Hammer Time on Sep 7, 2012, 6:37 PM)
|
|
| |
|
|
greasy one
User
Sep 7, 2012, 7:19 PM
Post #5 of 13
(2526 views)
|
|
Re: Ticking Subaru
|
Sign In
|
|
Thanks for your time, I do have some 1/2"Sockets, but not impact, also the pipe from floor jack. That should break anything loose. I have been looking around the site and picking up tips. Wish my pal Bob from Gulf Shores, Al. was still around.
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Sep 7, 2012, 7:21 PM
Post #6 of 13
(2523 views)
|
|
Re: Ticking Subaru
|
Sign In
|
|
If you put that pipe on the average 1/2" ratchet, you'll turn it into a paperweight.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
Tom Greenleaf
Ultimate Carjunky
/ Moderator
Sep 8, 2012, 5:09 AM
Post #7 of 13
(2508 views)
|
|
Re: Ticking Subaru
|
Sign In
|
|
Greasyone: Quote">>I do have some 1/2"Sockets, but not impact, also the pipe from floor jack. That should break anything loose.<<"
Just a note on that. Yes you can get the leverage like that with some things but not the
"rattling" effect of good air power which is much less likely to bend or break things.
Even my own trick with air is capcity of storage not so much how fast. Can put an air can and do in a car's trunk
to fit air tools tip for a one shot deal away from shop and same can hooked up as extra capacity.
You need something if only for rare use more than just brute leverage for some things or send that out,
T
|
|
| |
|
|
Discretesignals
Ultimate Carjunky
/ Moderator
Sep 8, 2012, 6:18 AM
Post #8 of 13
(2500 views)
|
|
Re: Ticking Subaru
|
Sign In
|
|
I'd probably use a 1/2" breaker bar with the wheels on the ground to break the axle nut loose if you don't have access to an impact gun. I'd be leery of using a 1/2 ratchet and a pipe. Especially if the ratchet is a flea market special.
Since we volunteer our time and knowledge, we ask for you to please follow up when a problem is resolved.
|
|
| |
|
|
greasy one
User
Sep 8, 2012, 8:04 AM
Post #9 of 13
(2489 views)
|
|
Re: Ticking Subaru
|
Sign In
|
|
Thanks to all, I am gonna head to Autozone, for possible rental, especially for that inner shaft. I have a Craftsman set of sockets and a smaller pipe, not too worried about that. The tips help thou. I had no idea what was involved and now know a little more.
|
|
| |
|
|
greasy one
User
Sep 8, 2012, 7:34 PM
Post #10 of 13
(2477 views)
|
|
Re: Ticking Subaru
|
Sign In
|
|
Well all fixed
by Firestone lol
|
|
| |
|
|
greasy one
User
Sep 9, 2012, 8:52 PM
Post #11 of 13
(2455 views)
|
|
Re: Ticking Subaru
|
Sign In
|
|
There was a headache at the end of the job. It was nothing compared to what would have been if I had tried to do this procedure myself. They were spinning the wheels, under power and the wheel was wobbling bad. They thought the rim was bent, at first, then the rotor. It turns out the rotor was a bit rusted up and a piece got knocked loose and was trapped when the kid put the rotor back on.
|
|
| |
|
|
nickwarner
Veteran
/ Moderator
Sep 10, 2012, 6:34 PM
Post #12 of 13
(2429 views)
|
|
Re: Ticking Subaru
|
Sign In
|
|
Congrats on the fix and glad it worked out for you.
|
|
| |
|
|
greasy one
User
Sep 10, 2012, 8:04 PM
Post #13 of 13
(2426 views)
|
|
Re: Ticking Subaru
|
Sign In
|
|
Thanks to all. The car had been shaking, for awhile, but better now. Got a good deal too.
|
|
| |
|
Auto Repair Home
SEARCH
WHO'S 
LOG 
1989 toyota pickup 3.0 crank no start
Please Help - Knock sound & engine fail
