|
|
|
350 tbi injector pulse prob.
|
|
|
| |
|
|
roger2791
User
Sep 2, 2010, 7:09 PM
Post #1 of 35
(14156 views)
|
|
350 tbi injector pulse prob.
|
Sign In
|
|
91 chevy silverado 1500 2wd step side 350 tbi lost injector pulse turned truck off and it would not start afterwards.
all fuses good truck will start and run w/starting fulid but dies when you stop spraying.
i can force the pulse on the injector with a test light between the purple w/white stripe wire off of the ing.module and the pos.side post of batt. so i know the injectors are good and its an new module (inside the dis.)
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Sep 2, 2010, 7:15 PM
Post #2 of 35
(14149 views)
|
|
Re: 350 tbi injector pulse prob.
|
Sign In
|
|
Are you losing the power side or the pulsing ground side?
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
roger2791
User
Sep 2, 2010, 7:23 PM
Post #3 of 35
(14145 views)
|
|
Re: 350 tbi injector pulse prob.
|
Sign In
|
|
i get power to the injector but will not pulse
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Sep 2, 2010, 7:25 PM
Post #4 of 35
(14141 views)
|
|
Re: 350 tbi injector pulse prob.
|
Sign In
|
|
Does the check engine light come on for bulb check when the key is first turned on?
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
roger2791
User
Sep 2, 2010, 7:33 PM
Post #5 of 35
(14137 views)
|
|
Re: 350 tbi injector pulse prob.
|
Sign In
|
|
yes light dose come on i also have a code stored. using jumper wire flashes code 12.32
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Sep 2, 2010, 7:36 PM
Post #6 of 35
(14133 views)
|
|
Re: 350 tbi injector pulse prob.
|
Sign In
|
|
That's an unrelated code. You could be looking at a bad ECM here but you need to first verify all the ECM grounds and the wiring to the injectors first.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
(This post was edited by Hammer Time on Sep 2, 2010, 7:37 PM)
|
|
| |
|
|
roger2791
User
Sep 2, 2010, 7:43 PM
Post #7 of 35
(14127 views)
|
|
Re: 350 tbi injector pulse prob.
|
Sign In
|
|
where do i get good wiring diag.
(This post was edited by roger2791 on Sep 2, 2010, 7:50 PM)
|
|
| |
|
|
Sidom
Veteran
/ Moderator
Sep 2, 2010, 8:20 PM
Post #8 of 35
(14123 views)
|
|
Re: 350 tbi injector pulse prob.
|
Sign In
|
|
Hmmmm..... This strange..... You are saying it's passing a "tap test".
I'm assuming you are using a noid light to check for pulse.....
You said the module is new...... The truck died and you just put a new module in it with the same results? or This module was new, already in the truck and it was running but now it died?
|
|
| |
|
|
roger2791
User
Sep 2, 2010, 9:07 PM
Post #9 of 35
(14118 views)
|
|
Re: 350 tbi injector pulse prob.
|
Sign In
|
|
changed the module after truck died because i could make the injectors fire with test light jumping it between wires coming out of moudule (purple w/ white stripe) and pos. term. of the batt. so silly me i assumed it was a module problem.
(This post was edited by roger2791 on Sep 2, 2010, 9:08 PM)
|
|
| |
|
|
roger2791
User
Sep 2, 2010, 9:10 PM
Post #10 of 35
(14116 views)
|
|
Re: 350 tbi injector pulse prob.
|
Sign In
|
|
but i was told that this means the E.C.M is good. is this also a bad assaumtion?
|
|
| |
|
|
Sidom
Veteran
/ Moderator
Sep 2, 2010, 11:30 PM
Post #11 of 35
(14113 views)
|
|
Re: 350 tbi injector pulse prob.
|
Sign In
|
|
With you getting a SES, flashing a 12 and passing the tap test it sure looks like its working.... As far as getting 2 modules doing the same thing, that's kinda out there to....
There is a few reasons why the PCM would shut down the pulse......It's late & my mind just aint movin that quick so I'll have to check all the reasons later..... One reason for sure, is WOT or clear flood. If the comp "thinks" you have it floored it'll shut off the pulse. Try disconnecting the TPS & see what that does (besides setting a code.. ). You said you have a 32. The is just an EGR code & while there is no ref voltage the PCM does ground it.... Just for the hellva it, disconnect the egr solenoid, it should be just to the right of the throttle body....
This is an exploded diagram of the PCM connecter......What is missing on this is just the injector wires going to the injectors & the injector power source.... The PCM use this signal along with some other inputs to determine the pulse width for the injectors (how much gas the engine needs)
Just for the heck of it......triple check all the fuses...........please
Another thought after looking at this diag a bit............. Double check all the connecters in the dist...... It really seems like the module isn't sending a signal out on ckt 430..... I'll have to ponder this some more.........it's late..........
(This post was edited by Sidom on Sep 2, 2010, 11:35 PM)
|
|
| |
|
|
roger2791
User
Sep 3, 2010, 12:47 PM
Post #12 of 35
(14097 views)
|
|
Re: 350 tbi injector pulse prob.
|
Sign In
|
|
triple chk fuse and they are fine. today have noticed green wire off of the pick up coil going to the ing. module insalation is cracked and wire exsposed but if i had a problem with the pick up coil wouldnt i also have a problem with the spark (no signal to the (ext.) ing. coil resulting in no spark)
(This post was edited by roger2791 on Sep 3, 2010, 12:52 PM)
|
|
| |
|
|
Sidom
Veteran
/ Moderator
Sep 3, 2010, 7:52 PM
Post #13 of 35
(14088 views)
|
|
Re: 350 tbi injector pulse prob.
|
Sign In
|
|
You know the one thing I didn't think about is there is a ground coming from the PCM to the module. I don't think it's a pickup coil either or it wouldn't run on starting fluid.....
Unfortunately my database is down. but if all the wires are good, new module and it's still not getting a pulse then HT is probably right and you may have a bad PCM........ This is where it would be real nice to have a "known good" tester to pop in real quick.....
IF you can't get a diagram for this.....I'll see if I can bring on from the shop.........
|
|
| |
|
|
roger2791
User
Sep 3, 2010, 9:56 PM
Post #14 of 35
(14084 views)
|
|
Re: 350 tbi injector pulse prob.
|
Sign In
|
|
you say a pcm? is this the same as ECM i didnt think this truck had a pcm its 91 but then again i dont know every thing or i would not be in this predicument. ha / ha. thanks for all your help its good to know that are still nice folks willing to help another when there down...
(This post was edited by roger2791 on Sep 3, 2010, 10:14 PM)
|
|
| |
|
|
Sidom
Veteran
/ Moderator
Sep 3, 2010, 10:23 PM
Post #15 of 35
(14081 views)
|
|
Re: 350 tbi injector pulse prob.
|
Sign In
|
|
Yea it's basically the same thing...... PCM, ECM, ECU are all acronyms for the engine computer... Manufacturers all have to use different terms for the same thing.
Like HT said, the powers and grounds have to be verified 1st before pulling the trigger on it. If you had one you could swap, I'd definitely try that, if not I would want to make sure there wasn't a bad wire 1st before buying one..........
I'll see if I can't find some diagrams for you or maybe HT has some he can post....
Just a footnote, GM has a bad habit of listing comp ground circuits as "low reference". It shouldn't be a problem for what you have to do, but when you are tracing ref voltage circuits it can really get confusing & misleading if you aren't aware of it...............
(This post was edited by Sidom on Sep 3, 2010, 10:27 PM)
|
|
| |
|
|
roger2791
User
Sep 3, 2010, 11:08 PM
Post #16 of 35
(14074 views)
|
|
Re: 350 tbi injector pulse prob.
|
Sign In
|
|
thanx.
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Sep 4, 2010, 4:57 AM
Post #17 of 35
(14067 views)
|
|
Re: 350 tbi injector pulse prob.
|
Sign In
|
|
Make sure this matches because there are some varying versions of this
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
Sidom
Veteran
/ Moderator
Sep 5, 2010, 11:02 AM
Post #18 of 35
(14052 views)
|
|
Re: 350 tbi injector pulse prob.
|
Sign In
|
|
Yea that's what I was thinking of HT.
Roger you can see the 12v & grounds on those pins. While it does run with carb clean it would still be a good idea to make sure there is no power or resistance problems on those and the 5v ref is good as well......
These are the connection you really want to make sure are good. 453 was the ground I forgot about going to the module. While you can get a pulse with the tap test. That means the pcm can generate a pulse, for what ever reason it's not getting a signal to generate a pulse (maybe?)..... These problems are a little tougher to check out with out a scope but not impossible... This is for your module. You can find the corresponding ckt numbers on HT diagram....
|
|
| |
|
|
roger2791
User
Sep 5, 2010, 12:31 PM
Post #19 of 35
(14044 views)
|
|
Re: 350 tbi injector pulse prob.
|
Sign In
|
|
thanx im checking now and i will get back with the results.. am i to check the pins with the connectors on or off the ecm
(This post was edited by roger2791 on Sep 5, 2010, 1:37 PM)
|
|
| |
|
|
roger2791
User
Sep 5, 2010, 1:38 PM
Post #20 of 35
(14034 views)
|
|
Re: 350 tbi injector pulse prob.
|
Sign In
|
|
am i to check the pins with the connectors on or off the ecm
|
|
| |
|
|
Sidom
Veteran
/ Moderator
Sep 5, 2010, 2:32 PM
Post #21 of 35
(14027 views)
|
|
Re: 350 tbi injector pulse prob.
|
Sign In
|
|
I would 1st disconnect both ends of the connecters and check them with an ohm meter both for continuity and grounding. The system powers and grounds you can check with the connecters disconnect & KOEO. The signals & PCM grounds you are going to have to check with the connecters hooked up, KOEO & back probed.
|
|
| |
|
|
roger2791
User
Sep 5, 2010, 3:30 PM
Post #22 of 35
(14019 views)
|
|
Re: 350 tbi injector pulse prob.
|
Sign In
|
|
all is right (12 volts & grounds) exept for b5 there is no ground and when you probe with test light looking for ground you here what sounds like the fuel pump priming the line. and a clicking of a relay switch.
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Sep 5, 2010, 3:47 PM
Post #23 of 35
(14013 views)
|
|
Re: 350 tbi injector pulse prob.
|
Sign In
|
|
The fuel pump trigger should be a Dk green and and white on A1.
B5 is the EST reference signal on most and a speed sensor on one of them.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
roger2791
User
Sep 5, 2010, 3:53 PM
Post #24 of 35
(14009 views)
|
|
Re: 350 tbi injector pulse prob.
|
Sign In
|
|
should it have ground (b5)
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Sep 5, 2010, 3:55 PM
Post #25 of 35
(14006 views)
|
|
Re: 350 tbi injector pulse prob.
|
Sign In
|
|
No. it's an ignition signal from a module. Don't be sending power down it. You have to be careful what your testing here.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
Auto Repair Home
SEARCH
WHO'S 
LOG 
1989 toyota pickup 3.0 crank no start
Please Help - Knock sound & engine fail
1
