|
|
starangel43
Novice
Sep 28, 2006, 9:42 PM
Post #1 of 9
(1975 views)
|
|
Discharging system
|
Sign In
|
|
I have a 1989 chevy cav Z24 and i have replaced the alt had the battery checked and it is good checked the fusible link with a test light it is good but it is still discharging can someone help me with ideas of where to go and check for what could be wrong i am at a loss.
|
|
| |
|
|
steve01832
Veteran
Sep 29, 2006, 2:49 AM
Post #2 of 9
(1973 views)
|
|
Re: Discharging system
|
Sign In
|
|
Take a test light and touch the heavy cable bolted to the back of the alternator. If the light is bright, next unplug the small regulator plug from alternator. Key on engine off. Touch test light to red wire. Test light should glow bright. Touch light to next wire. The dash indicator should come on. If wiring tests OK take test light from Battery + and touch alternator case. If light glows bright, replace alternator. I have had many remanufactured alternators be junk right out of the box. Post back and let us know.
|
|
| |
|
|
starangel43
Novice
Sep 29, 2006, 8:14 AM
Post #3 of 9
(1965 views)
|
|
Re: Discharging system
|
Sign In
|
|
 I have done all of that and all test good even altnator was retest by the parts store and tested 14.5
|
|
| |
|
|
Tom Greenleaf
Ultimate Carjunky
/ Moderator
Sep 29, 2006, 11:34 AM
Post #4 of 9
(1963 views)
|
|
Re: Discharging system
|
Sign In
|
|
Does this behave when you are driving but discharges over a period of time?
If so check for a drain which should only be one circuit, T
|
|
| |
|
|
DanD
Veteran
/ Moderator
Sep 29, 2006, 11:39 AM
Post #5 of 9
(1963 views)
|
|
Re: Discharging system
|
Sign In
|
|
Maybe if we start from the beginning we’ll be able to help you figure this out. What I would like you to do is take a voltage reading at the battery without the engine running; this is of course after you’ve had the battery charged and tested making sure that it is still in good condition.
Next would be to start the engine and take a second voltage reading at the battery.
With the engine running the voltage should increase by 2 to 3 volts with in the first 15 to 20 seconds.
Does it?
Dan.
Canadian "EH"
|
|
| |
|
|
starangel43
Novice
Sep 30, 2006, 12:57 PM
Post #6 of 9
(1952 views)
|
|
Re: Discharging system
|
Sign In
|
|
ok volt metter reading done when the car off it is reading 13 and when it is running drops to 12 or 11 it is gettting very low output
[Teresa)
(This post was edited by starangel43 on Sep 30, 2006, 2:43 PM)
|
|
| |
|
|
starangel43
Novice
Sep 30, 2006, 2:48 PM
Post #7 of 9
(1949 views)
|
Re: Discharging system
|
Sign In
|
|
|
|
| |
|
|
starangel43
Novice
Sep 30, 2006, 2:52 PM
Post #8 of 9
(1947 views)
|
|
Re: Discharging system
|
Sign In
|
|
HAve done everything possible altinator, fusible link,new battery, have even checked volts running and off volts running is 11 and off is 13.
|
|
| |
|
|
DanD
Veteran
/ Moderator
Oct 2, 2006, 4:16 AM
Post #9 of 9
(1942 views)
|
|
Re: Discharging system
|
Sign In
|
|
Here’s a typical wiring diagram for an 89 Cavalier.
It’s showing two fusible links down at the starter; there may only be one having the two different sized Black/red wires. Both wires should have battery voltage on them regardless of ignition switch position. Hook your finger around these fuse links and give them a fairly hard pull. I’ve seen fusible links burn out but leave the insulation in tact; allowing them too visually look ok but open electrically.
The Brown/white wire feeds the field circuit of the alternator; it’s protected by either a 10amp or 20 amp fuse (depending on what style of dash your car has) It should have source voltage (battery) on it when the ignition is in the run position.
The last circuit is the warning system (again depending on the dash configuration). The brown wire should show power when disconnected from the alternator while using a test light, that’s with the ignition switch in any position other then off. A quick easy way to check the warning system (if your dash as a warning light) Is to leave everything connected; turn on the ignition engine off; you should have the warning light on. If so you can forget it, it’s working. If its not coming on disconnect the connector that houses the brown wire at the alternator and take the brown wire only to ground; the dash light should come on. If the light comes on while the brown wire is connected to ground then the problem is still in the alternator. Some GM alternators need this warning light to function to kind of jump-start the alternator to get it charging.
Hope I didn’t add to the confusion if so tell me where I lost you.
Dan.
Canadian "EH"
|
|
| |
|
| | |
|
Auto Repair Home
SEARCH
WHO'S 
LOG 
1989 toyota pickup 3.0 crank no start
Please Help - Knock sound & engine fail
