|
|
rogdukes
New User
Feb 13, 2011, 2:36 PM
Post #1 of 6
(1667 views)
|
My 2003, Ford F150 Supercrew's automatic door locks quit working. I didn't worry about this because all other things were working correctly. Recently one of our two key fobs went bad but the other worked fine. We tried reprograming it and it would not program. We replaced it and the system will not program the fobs. We have followed the programing directions to the "T". In the past we reprogamed the fobs for our Town Car without a problem. Is there something in the system I need to replace or is this a dealer only repair.
Thanks,
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Feb 13, 2011, 2:41 PM
Post #2 of 6
(1663 views)
|
|
Re: Power door locks
|
Sign In
|
|
Remember, they all have the be programmed at the same time, even the ones that were working because your changing the password.
Here is the procedure
REMOTE TRANSMITTER PROGRAMMING
NOTE:
- All keyless entry remote transmitters must be programmed at the same time.
- Programming (or reprogramming) the keyless entry remote transmitters into the central security module can be accomplished using a diagnostic tool or by carrying out the following steps.
- Turn the ignition switch from OFF to RUN eight times within 10 seconds , ending in RUN. If the module has successfully entered program mode, it will lock and then unlock all doors.
- Within 20 seconds , press any button on a keyless entry remote transmitter, and the doors will lock and then unlock to confirm that each keyless entry remote transmitter has been programmed. Repeat this step for each transmitter.
- If the door locks do not respond for any keyless entry remote transmitter, wait several seconds and press the button again. If the door locks still fail to respond, refer to Inspection and Verification.
- Turn the ignition switch to the OFF position, or wait up to 20 seconds after Step 2, to exit program mode. If a keyless entry remote transmitter has been programmed (or reprogrammed), the doors will lock and unlock one last time to confirm.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
Tom Greenleaf
Ultimate Carjunky
/ Moderator
Feb 13, 2011, 2:43 PM
Post #3 of 6
(1661 views)
|
|
Re: Power door locks
|
Sign In
|
|
Never mind the fobs for now. Will they work from button inside and do they work plain manually?
T
|
|
| |
|
|
rogdukes
New User
Feb 13, 2011, 2:52 PM
Post #4 of 6
(1656 views)
|
|
Re: Power door locks
|
Sign In
|
|
The locks will not work when truck is put in gear. All else works as it should except that the fobs will not reprogram.
|
|
| |
|
|
rogdukes
New User
Feb 13, 2011, 2:54 PM
Post #5 of 6
(1655 views)
|
|
Re: Power door locks
|
Sign In
|
|
This has all be done. Fobs will not reprogram
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Feb 13, 2011, 3:11 PM
Post #6 of 6
(1652 views)
|
|
Re: Power door locks
|
Sign In
|
|
Then you're going to have to go to the dealer so they can use a scan tool on it.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
Auto Repair Home
SEARCH
WHO'S 
LOG 
1989 toyota pickup 3.0 crank no start
Please Help - Knock sound & engine fail
