Connect

Car Pictures

Shopping

Classifieds

News & Articles

Car Forums

Automotive Links

(Bookmark CarJunky)

	Auto Repair Home	SEARCH POSTS	WHO'S ONLINE	LOG IN

Automotive Repair Car Troubleshooting Topics   Car Troubleshooting   Engine Troubleshooting   Engine Fault Codes   Electrical and Wiring   Transmission Problems Car Repair Topics   Car Making Noises   Car Stereo Repair   Heating or AC Issues   Motorcycles and ATVs   Tricks of the Trade   Truck Repair Advice Site Options:      Login   Sign up here! Latest Forum Post   1989 toyota pickup 3.0 crank no start I have a 1989 toyota pickup 3.0 crank no...   Strut spring orientation and strut mount tension nut 2017 Nissan rogue awd 2.5 L Put in Monro...   Transmission stuck in part, I have tried everything So I'm working on my elderly fathers 201...   2017 dodge journey LED headlights on/off randomly Year of vehicle 2017 Make of vehicle dod...   Kia Soul starter replacement issues! Okay so my car is a 2010 Kia soul 2.0 en...   Please Help - Knock sound & engine fail Hi all, Hoping to get some insight and ...   multiple warning lights 2013 GMC Terrain 130,000 miles 4 cylinde...   03 alero no low speed blower Good day everyone, I have a 2003 Olds a...   04 Chevy 2500hd tail light issues Help!!! I have changed my combo switch...   1999 Grand Caravan Sport not starting. Hi. I'm new here. I hope someone can hel...

02 dakota 3.9 knocking valve Sign up here! Search this forum this category all forums for All words Any words Whole Phrase (search options) Auto Repair Home>> Automotive Repair>> Engine Troubleshooting natdog New User Sep 2, 2012, 11:33 AM Post #1 of 5 (1965 views) 02 dakota 3.9 knocking valve Sign In I recently changed my oil and filter, but slightly overfilled. I ran it for a few to fill the filter. I drined back to normal level. ever since theres a knock on acceleration and deceleration around 2500 and 2000 rpm. thats when it is the worst. any ideas? Vacuum leak, valve adjust???? Tom Greenleaf Ultimate Carjunky / Moderator Sep 2, 2012, 11:49 AM Post #2 of 5 (1960 views) Re: 02 dakota 3.9 knocking valve Sign In How much too full? That will matter and was vehicle on an angle when first started? Late for this oil change but when possible fill the filter to minimize the time for oil pressure to be at normal fast on start up. Does oil pressure read normal and fast on start up now? Can't know but it is possible to hurt things quite quickly with overfill or under filled, T natdog New User Sep 2, 2012, 12:15 PM Post #3 of 5 (1932 views) Re: 02 dakota 3.9 knocking valve Sign In about a quart over full! and level when starting. In Reply To natdog New User Sep 2, 2012, 12:22 PM Post #4 of 5 (1929 views) Re: 02 dakota 3.9 knocking valve Sign In It reads normal now. It akes a second or two to get up there. Tom Greenleaf Ultimate Carjunky / Moderator Sep 2, 2012, 12:52 PM Post #5 of 5 (1917 views) Re: 02 dakota 3.9 knocking valve Sign In Basic oil changing: Warm engine. Drain oil and remove old filter. When possible fill new oil filter, lube with clean oil the rubber gasket. Tighten as per instructions on filter or packaging. Start engine when properly filled and circulated - any warnings of low oil pressure upon first start should go away quickly and allow to warm up a bit. Shut down and wait for oil to return to oil pan. With dipstick check for proper oil level on level ground and for leaks from any drain plug and filter while running. Other items on check list done at oil change intervals as listed in owner's manual. Dispose of used oil and filter as per local requirements. __________________________ This is highly routine and perhaps the most DIY maintenance done to vehicles. Initial start ups there is a period of extended time for oil pressure to get to normal as it would fill oil filter first and all would normally be fine. If a prolonged run with no oil pressure or if overfilled but not usually just one quart if known only that is the short critical time. Under by a lot engine bearings can take a hit. Over filled could make crankshaft splash in oil with assorted problems some very serious. Older and the weak links of anything under oil pressure would be hit first or oil splashing hard in the wrong places could damage lower end moving parts. IDK exact layout of everything ever made. If things had to be removed to access drain plug or oil filter those all need to be put back as intended. Pretty much I'd have to hear it in person now as this knocking seemed to be exactly related to this oil change service and if not just some shield that wasn't put back properly diagnose out what is making this knock now. Apparently driven a bit now with the knocking so if real engine problem develped not just some item that was touched to do this it will need to be diagnosed out and again if real damage it's done and wont get better by itself, T   Automotive Repair     Auto Body Repair and Refinishing     Heating or AC Issues     Electrical and Wiring     Brake Systems     Car Stereo Repair Advice     General Discussions     Car Making Funny Noises     Engine Fault Codes     Engine Troubles     Exhaust Systems     Steering and Suspension     Transmission Troubles     Tricks of the Trade Automotive World     General Discussions     Antique Car Talk     Car Shows and Events     The Bargin Bin     Motor Vehicle Inspection     Car Care Tips     Traffic Tickets     Gasoline, Motor Oils, Concept Cars and Engines     Auto Insurance, Financing, Leases, Warranties Truck Repair     General Discussions     Truck Engine Repair     Truck Suspension Repair Motorcycle Repair     General Discussions     Motorcycle Engine Repair CarJunky     Open Posting     Board FAQ's     New Board Suggestions

Search this forum this category all forums for All words Any words Whole Phrase (options)

Privacy Sitemap