Main IndexAuto Repair Home Search Posts SEARCH
POSTS 		Who's Online WHO'S
ONLINE 		Log in LOG
IN




Automotive Repair
Car Troubleshooting Topics
  Car Troubleshooting
  Engine Troubleshooting
  Engine Fault Codes
  Electrical and Wiring
  Transmission Problems

Car Repair Topics
  Car Making Noises
  Car Stereo Repair
  Heating or AC Issues
  Motorcycles and ATVs
  Tricks of the Trade
  Truck Repair Advice

Site Options:   
  Login
  Sign up here!



Latest Forum Post
with_replies.gif image   Carbon Fiber parts/concern
Im a bit of a hypochondriac so when I sa...

with_replies.gif image   Battery woes 2010 Ranger 4.0
This vehicle is not a daily driver , I s...

hot_with_replies.gif image   This isn't normal, right?
Gap between connections on exhaust. I be...

with_replies.gif image   Lukewarm Heat............
New antifreeze reverse flush heater core...

with_replies.gif image   multiple warning lights
2013 GMC Terrain 130,000 miles 4 cylinde...

with_replies.gif image   2014 Nissan Sentra Shaking
Car recently started shaking when accele...

no_replies.gif image   Buy Flualprazolam Powder Online Whatsapp: +1(424) 328-1086
N/A

hot_with_replies.gif image   1989 toyota pickup 3.0 crank no start
I have a 1989 toyota pickup 3.0 crank no...

with_replies.gif image   Strut spring orientation and strut mount tension nut
2017 Nissan rogue awd 2.5 L Put in Monro...

with_replies.gif image   Transmission stuck in part, I have tried everything
So I'm working on my elderly fathers 201...




1996 Mercury Villager PO325 code

Search for (search options)
 



lawsontw
New User

Jan 24, 2007, 2:55 PM

Post #1 of 4 (6366 views)
post icon 1996 Mercury Villager PO325 code Sign In
Help needed for 96 Mercury Villager...when cold van starts fine but runs for 15 - 30 minutes then will start to miss and run rough until it eventually will die. If codes checked at that time before starting I get a PO325 Knock Sensor 1 circuit malfuntion Bank 1 or 1 Sensor. Have replaced plugs, wires, distributor cap,rotor,fuel filter, ignition coil, (power transistor)i.e. ignition control module no help. Everytime after engine cools it starts again and runs about 20 minutes. Could this be catalytic converter or exhaust related? Have tried when it dies to spray starter fluid in throttle body but will not start.

Thanks in advance!!!


DanD
Veteran / Moderator
DanD profile image

Jan 24, 2007, 3:25 PM

Post #2 of 4 (6363 views)
Re: 1996 Mercury Villager PO325 code Sign In
When its not starting what’s missing; spark, fuel pressure or injector pulse?
We would need this information to even begin suggesting anything.
Dan.

Canadian "EH"






lawsontw
New User

Jan 25, 2007, 10:43 AM

Post #3 of 4 (6356 views)
post icon Re: 1996 Mercury Villager PO325 code Sign In
Hi Dan,
Im trying to check all of that with the limited equipment I have. When it gets to operating tempeture it starts running
rough then dies. When I turn ignition on I get several clicks then they stop? Is it posible the fuel pump could quit
like that when warm same time every time?
Thanks,
Tom


DanD
Veteran / Moderator
DanD profile image

Jan 25, 2007, 11:58 AM

Post #4 of 4 (6353 views)
Re: 1996 Mercury Villager PO325 code Sign In
Sure almost anything is possible but you don’t want to be throwing parts at this thing on guesses.
Dan.

Canadian "EH"









 
 
 






Search for (options) Privacy Sitemap