|
|
|
1998 caviler camshaft position sensor
|
|
|
| |
|
|
jordanpowers
New User
Apr 10, 2015, 3:48 PM
Post #1 of 7
(1243 views)
|
|
1998 caviler camshaft position sensor
|
Sign In
|
|
I have a 1998 caviler 2.2. I was driveing it one days and it just died and when I tryed to start it it just clicks, I got it towed home and I hooked it up to computer and the only code that came up was for the camshaft positioner sensor. So I changes that and still only clicked so I changed battery and starter and still nothen but click. What could it be
|
|
| |
|
|
Discretesignals
Ultimate Carjunky
/ Moderator
Apr 10, 2015, 3:55 PM
Post #2 of 7
(1240 views)
|
|
Re: 1998 caviler camshaft position sensor
|
Sign In
|
|
What is making the clicking noise?
If it just clicks and the engine doesn't crank, you should be troubleshooting the starting system. Do you have power to the small purple wire on the starter solenoid when you have someone attempt to crank the engine?
Since we volunteer our time and knowledge, we ask for you to please follow up when a problem is resolved.
(This post was edited by Discretesignals on Apr 10, 2015, 3:58 PM)
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Apr 10, 2015, 4:59 PM
Post #3 of 7
(1225 views)
|
|
Re: 1998 caviler camshaft position sensor
|
Sign In
|
|
Before you waste too much time troubleshooting you might want to put a socket and breaker bar on the crankshaft bolt and see if you can turn the engine by hand and make sure it's not seized up.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
jordanpowers
New User
Apr 11, 2015, 2:33 PM
Post #4 of 7
(1203 views)
|
|
Re: 1998 caviler camshaft position sensor
|
Sign In
|
|
engine is not seize and I have it cranking over now but will not fire off. I have spark and Ist getting fuel.
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Apr 11, 2015, 2:38 PM
Post #5 of 7
(1199 views)
|
|
Re: 1998 caviler camshaft position sensor
|
Sign In
|
|
All "crank, no start" conditions are approached in the same way. Every engine requires certain functions to be able to run. Some of these functions rely on specific components to work and some components are part of more than one function so it is important to see the whole picture to be able to conclude anything about what may have failed. Also, these functions can ONLY be tested during the failure. Any other time and they will simply test good because the problem isn't present at the moment.
If you approach this in any other way, you are merely guessing and that only serves to replace unnecessary parts and wastes money.
Every engine requires spark, fuel and compression to run. That's what we have to look for.
These are the basics that need to be tested and will give us the info required to isolate a cause.
1) Test for spark at the plug end of the wire using a spark tester. If none found, check for power supply on the + terminal of the coil with the key on.
2) Test for injector pulse using a small bulb called a noid light. If none found, check for power supply at one side of the injector with the key on.
3) Use a fuel pressure gauge to test for correct fuel pressure, also noticing if the pressure holds when key is shut off.
4) If all of these things check good, then you would need to do a complete compression test.
Once you have determined which of these functions has dropped out,
you will know which system is having the problem.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
Discretesignals
Ultimate Carjunky
/ Moderator
Apr 11, 2015, 3:52 PM
Post #6 of 7
(1193 views)
|
|
Re: 1998 caviler camshaft position sensor
|
Sign In
|
|
Is the cam code still popping up? What is the code number?
Since we volunteer our time and knowledge, we ask for you to please follow up when a problem is resolved.
|
|
| |
|
|
jordanpowers
New User
Apr 11, 2015, 8:50 PM
Post #7 of 7
(1185 views)
|
|
Re: 1998 caviler camshaft position sensor
|
Sign In
|
|
I can't remember the code number and now there is no codes showing
|
|
| |
|
Auto Repair Home
SEARCH
WHO'S 
LOG 
Lukewarm Heat............
Buy Flualprazolam Powder Online Whatsapp: +1(424) 328-1086
1989 toyota pickup 3.0 crank no start
