Main IndexAuto Repair Home Search Posts SEARCH
POSTS 		Who's Online WHO'S
ONLINE 		Log in LOG
IN




Automotive Repair
Car Troubleshooting Topics
  Car Troubleshooting
  Engine Troubleshooting
  Engine Fault Codes
  Electrical and Wiring
  Transmission Problems

Car Repair Topics
  Car Making Noises
  Car Stereo Repair
  Heating or AC Issues
  Motorcycles and ATVs
  Tricks of the Trade
  Truck Repair Advice

Site Options:   
  Login
  Sign up here!



Latest Forum Post
with_replies.gif image   1989 toyota pickup 3.0 crank no start
I have a 1989 toyota pickup 3.0 crank no...

with_replies.gif image   Strut spring orientation and strut mount tension nut
2017 Nissan rogue awd 2.5 L Put in Monro...

with_replies.gif image   Transmission stuck in part, I have tried everything
So I'm working on my elderly fathers 201...

with_replies.gif image   2017 dodge journey LED headlights on/off randomly
Year of vehicle 2017 Make of vehicle dod...

with_replies.gif image   Kia Soul starter replacement issues!
Okay so my car is a 2010 Kia soul 2.0 en...

hot_with_replies.gif image   Please Help - Knock sound & engine fail
Hi all, Hoping to get some insight and ...

with_replies.gif image   multiple warning lights
2013 GMC Terrain 130,000 miles 4 cylinde...

with_replies.gif image   03 alero no low speed blower
Good day everyone, I have a 2003 Olds a...

with_replies.gif image   04 Chevy 2500hd tail light issues
Help!!! I have changed my combo switch...

with_replies.gif image   1999 Grand Caravan Sport not starting.
Hi. I'm new here. I hope someone can hel...




2000 Pontiac Ignition Problem

Search for (search options)
 



cpharr
New User

Nov 18, 2008, 5:12 PM

Post #1 of 3 (4308 views)
2000 Pontiac Ignition Problem Sign In
I have a 2000 Pontiac Bonneville, 3.8, 118k miles and it is not firing on 1&4. I can pull the wires from the ignition coil to verify this, so I replace the coil and still have no spark from this coil. What else can cause this, maybe the Ignition Control Module? If so, where is it located at and how can I verify that this is what I need without buying one first?

Thanks in advance for any help.


Loren Champlain Sr
Veteran / Moderator
Loren Champlain Sr profile image

Nov 18, 2008, 5:48 PM

Post #2 of 3 (4302 views)
Re: 2000 Pontiac Ignition Problem Sign In
My first instinct would be the control module, BUT, have you pulled codes yet? Could be a (PCM) driver problem.
(The control module is what the coils are mounted on).
Loren
SW Washington


autojoe
User

Nov 19, 2008, 4:32 PM

Post #3 of 3 (4290 views)
Re: 2000 Pontiac Ignition Problem Sign In
  1. Install a spark tester at the spark plug end of the ignition wire associated with the misfiring cylinders hooked to good ground.
  2. Jumper the spark plug end of the companion cylinder ignition wire to engine ground. The companion cylinder is the cylinder that shares the same ignition coil (i.e. 1/4, 2/5, 3/6).
  3. Crank the engine while observing the spark tester.
  4. Then reverse and see if spark on both 1/4.
  5. Measure the resistance of the ignition wires associated with the cylinders that were indicated as misfiring. (1000-1500 ohms per foot)If not in spec. replace wires.
  • disconnect the ignition coil for cylinders 1/4.
  • Connect a test lamp across the ignition module primary circuit terminals.
  • Remove the fuel injector fuse.
  • Observe the test lamp while cranking the engine.

    • Does the test lamp blink?
    If not,replace Ignition control unit.All connections tight where coil sits on module terminals and also electrical connections.?Secondary resistance of coil should be between 5-8,000 ohms.
    They do make dis ignition module testers but pretty expensive.I don't know if any local parts stores have them.Could call and see.ICM easy to replace,just remove coils and then remove ICM.I usually check coil if having a problem with one is switch coil and see if problem follows coil.Just some thoughts.





     
     
     






    Search for (options) Privacy Sitemap