2001 Protege Cylinder Head - Engine Troubleshooting


	Auto Repair Home	SEARCH POSTS	WHO'S ONLINE	LOG IN

Automotive Repair

Car Troubleshooting Topics
  Car Troubleshooting
  Engine Troubleshooting
  Engine Fault Codes
  Electrical and Wiring
  Transmission Problems

Car Repair Topics
  Car Making Noises
  Car Stereo Repair
  Heating or AC Issues
  Motorcycles and ATVs
  Tricks of the Trade
  Truck Repair Advice

Site Options:
  Login
  Sign up here!

Latest Forum Post

Lukewarm Heat............

New antifreeze reverse flush heater core...

multiple warning lights

2013 GMC Terrain 130,000 miles 4 cylinde...

2014 Nissan Sentra Shaking

Car recently started shaking when accele...

Buy Flualprazolam Powder Online Whatsapp: +1(424) 328-1086

N/A

1989 toyota pickup 3.0 crank no start

I have a 1989 toyota pickup 3.0 crank no...

Strut spring orientation and strut mount tension nut

2017 Nissan rogue awd 2.5 L Put in Monro...

Transmission stuck in part, I have tried everything

So I'm working on my elderly fathers 201...

2017 dodge journey LED headlights on/off randomly

Year of vehicle 2017 Make of vehicle dod...

Kia Soul starter replacement issues!

Okay so my car is a 2010 Kia soul 2.0 en...

Please Help - Knock sound & engine fail

Hi all, Hoping to get some insight and ...

2001 Protege Cylinder Head

Sign up here!

Search for (search options)

Auto Repair Home>> Automotive Repair>> Engine Troubleshooting

ProtegeJunkie
New User

Mar 25, 2011, 12:59 PM

Post #1 of 4 (2465 views)

2001 Protege Cylinder Head	Sign In

I recently purchased a used cylinder head for my 2001 2.0L mazda protege. The cylinder head was rebuilt and all machining had been done before I bought it. However, it did not come with journal caps for the camshafts. I was told that I needed a cam bore alignment to ensure that the camshafts spun freely during engine operation. Is cam bore alignment the proper terminology here? Some people seem to not know what I'm talking about.

zmame
Veteran / Moderator
zmame profile image

Mar 25, 2011, 3:00 PM

Post #2 of 4 (2455 views)

Re: 2001 Protege Cylinder Head	Sign In

you will have to take it to machine shop.. they will measure the cam make sure it's not true, journals are not scored or worn and see if they are out of round.. depending how much they take off they will have to get bigger bearings to accommodate..

usually need V-blocks, dial indicator, plati-gauge and equipment to machine(if necessary).. and might need some special tools to install bearings depending on style.

ProtegeJunkie
New User

Mar 25, 2011, 8:18 PM

Post #3 of 4 (2444 views)

Re: 2001 Protege Cylinder Head	Sign In

My car does not have cam bearings. I was told the machine shop would not need the camshafts, just the head and journal caps

zmame
Veteran / Moderator
zmame profile image

Mar 25, 2011, 11:01 PM

Post #4 of 4 (2438 views)

Re: 2001 Protege Cylinder Head	Sign In

Bearings or not they still need to put it together and check journal bores make sure they are not out of round, scored or worn.. its good idea to have cam checked you put scored cam in new head your just going to eat away your journals.. also good to setup in V blocks and check make wire the condition of the cam it self.. and it will need to be fitted and checked clearances with plasti-gauge.. incorrect clearances cause all sorts of damage to your new head.

also they will check lobes see how much they have worn over its life.. it may be below minimum spec too.

Search for (options) Privacy Sitemap