|
|
jtw3
User
Aug 16, 2009, 3:44 AM
Post #1 of 9
(12391 views)
|
|
90 chevy 350 timing
|
Sign In
|
|
i replaced the distributor in my 90 chevy truck 350 motor. tried to keep the distributor on the same mark. it will turn over but will not start. how do i reset the timing?
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Aug 16, 2009, 6:10 AM
Post #2 of 9
(12384 views)
|
|
Re: 90 chevy 350 timing
|
Sign In
|
|
Ignition Timing
Caution: To prevent possible personal injury from a moving vehicle or operating engine do the following before performing the checks:
- Engage the parking brake and block the wheels.
- Place the automatic transmission in park or the manual transmission in neutral.
- Refer to the Vehicle Emissions Control Information label located on the radiator support panel. Follow all instructions on the label.
- Refer to the Fuel and Emissions Service Manual for information on the bypass timing mode.
- With the engine control switch off, connect the pickup lead of the timing lamp to the number one spark plug. Use a jumper lead between the wire and plug or an inducting type pickup. DO NOT pierce the wire or attempt to insert a wire between the boot and the wire. Connect the timing lamp power leads according to the manufacturer's instruction.
- Follow all instructions on the Vehicle Emissions Control Information label. Start the engine, and aim the timing lamp at the timing mark. The line on the balancer or pulley will line up at the timing mark. If a change in necessary, loosen the distributor hold-down clamp bolt at the base of the distributor. While observeing the mark with the timing lamp, slightly rotate the distributor until the line indicates the correct timing. Tighten the hold-down bolt, and recheck the timing.
- Turn off the engine and remove the timing lamp. Reconnect the number one spark plug wire, if removed.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
Sidom
Veteran
/ Moderator
Aug 16, 2009, 7:24 AM
Post #3 of 9
(12379 views)
|
|
Re: 90 chevy 350 timing
|
Sign In
|
|
Was the truck running before you r&r'd the dist? If so you need to make sure you're on #1. Pull the #1 plug, bring it up on compression, put the timing mark on TDC & pull the dist cap and make sure it's pointing @ #1.
Is it trying to start? backfiring? spuddering?
|
|
| |
|
|
jtw3
User
Aug 17, 2009, 12:19 AM
Post #4 of 9
(12374 views)
|
|
Re: 90 chevy 350 timing
|
Sign In
|
|
yes it backfirs and spits. how do i know which post on the distributor cap should be the number one post? on the inside of the cap there is a number one near a post, is that it. i dont think that is where the number one wire was to start.
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Aug 17, 2009, 12:30 AM
Post #5 of 9
(12370 views)
|
|
Re: 90 chevy 350 timing
|
Sign In
|
|
1990 Chevrolet C 1500 P/U 2WD
5.7 liter V-8 VIN "K" 
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
jtw3
User
Aug 17, 2009, 6:48 AM
Post #6 of 9
(12363 views)
|
|
Re: 90 chevy 350 timing
|
Sign In
|
|
thanks, i will try that and see if it starts this time.
|
|
| |
|
|
jtw3
User
Aug 17, 2009, 11:37 AM
Post #7 of 9
(12358 views)
|
|
Re: 90 chevy 350 timing
|
Sign In
|
|
thanks i think i put it on tdc and the rotor towards number one and it turns over but does not fire. dont know, thanks anyway.
|
|
| |
|
|
Loren Champlain Sr
Veteran
/ Moderator
Aug 17, 2009, 12:29 PM
Post #8 of 9
(12354 views)
|
|
Re: 90 chevy 350 timing
|
Sign In
|
|
jtw; Disconnect the connector to the coil so that it won't spark. Remove #1 spark plug. Have someone 'bump' over the engine until you feel the 'push' of air from the cylinder. You can do this with your finger on the hole, or with a compression guage. As soon as you feel that 'push' of air, you will be nearing Top Dead Center. Then, very carefully, align the timing marks at TDC. Remove the distributor cap and see where the rotor is pointing. It should be pointing to where #1 spark plug wire is connected. Follow HT's firing order. Remember, the crankshaft will go around twice. Only one is the 'compression' stroke. The other is exhaust stroke. You must be on the 'compression' stroke for TDC.
Loren
SW Washington
|
|
| |
|
|
Sidom
Veteran
/ Moderator
Aug 17, 2009, 2:33 PM
Post #9 of 9
(12349 views)
|
|
Re: 90 chevy 350 timing
|
Sign In
|
|
Was the truck running before you swapped distributors???????
|
|
| |
|
Auto Repair Home
SEARCH
WHO'S 
LOG 
1989 toyota pickup 3.0 crank no start
Please Help - Knock sound & engine fail
