|
|
mightymax
New User
Dec 8, 2009, 6:16 PM
Post #1 of 7
(4637 views)
|
|
92 mighty max no power
|
Sign In
|
|
I have a 1992 mitsubishi pickup called a mighty max. It's 2wd with a 2.4L in it. Ive replaced the spark plugs fuel regulator and the mass air flow sensor on the vehicle. Before i replaced those two parts the truck would run for 5 min then die. When i would check the spark plugs the plugs would be soaked with gas. After changing these parts the truck will sit and idle but after moving the truck about 10 ft the truck looses power and dies. What do i need to do. the truck has 130,000,miles on it.
|
|
| |
|
|
steve01832
Veteran
Dec 8, 2009, 6:21 PM
Post #2 of 7
(4631 views)
|
|
Re: 92 mighty max no power
|
Sign In
|
|
When the truck dies, will it immediately restart or will it crank over and not start?
Steve
|
|
| |
|
|
Loren Champlain Sr
Veteran
/ Moderator
Dec 8, 2009, 6:22 PM
Post #3 of 7
(4631 views)
|
|
Re: 92 mighty max no power
|
Sign In
|
|
mightymax; Sounds as if it is overfueling. Check the CTS (coolant temp sensor) and the connection. We can supply a chart for you, if needed, to check resistance at varying temps. I went ahead and attached the chart.
Loren
SW Washington
|
|
Attachments:
|
CTS chart.gif
(53.0 KB)
|
|
| |
|
|
mightymax
New User
Dec 8, 2009, 6:23 PM
Post #4 of 7
(4629 views)
|
|
Re: 92 mighty max no power
|
Sign In
|
|
it wont start
|
|
| |
|
|
steve01832
Veteran
Dec 8, 2009, 6:27 PM
Post #5 of 7
(4625 views)
|
|
Re: 92 mighty max no power
|
Sign In
|
|
If it won't start, let's install a fuel pressure guage into the fuel rail, install a noid light into one of the injector pigtails, and a spark tester on one of the coil wires. If you have a vacuum guage, tee into the pcv hose. Crank engine and observe all test equipment. Please record fuel pressure and crank vacuum readings and post back here. Also tell us if there is or isn't spark and whether or not it has injector pulse.
Steve
|
|
| |
|
|
Loren Champlain Sr
Veteran
/ Moderator
Dec 8, 2009, 6:28 PM
Post #6 of 7
(4624 views)
|
|
Re: 92 mighty max no power
|
Sign In
|
|
Pull the plugs again and dry them out. When you try to start it again, hold the throttle to the floor. This will enable a 'clear flood'. If the engine starts, back out of the throttle so you don't over-rev the engine. There are a multiude of things that could be going on, here, but I'm assuming that the engine is just flooding. Spark, cam timing, ect. are okay?
Loren
SW Washington
|
|
| |
|
|
mightymax
New User
Dec 8, 2009, 6:35 PM
Post #7 of 7
(4619 views)
|
|
Re: 92 mighty max no power
|
Sign In
|
|
do any of you guys have a chart or a diagram as to where some of these things may be. Im not all that engine savy.
|
|
| |
|
Auto Repair Home
SEARCH
WHO'S 
LOG 
1989 toyota pickup 3.0 crank no start
Please Help - Knock sound & engine fail
