|
|
jh
New User
Sep 21, 2009, 10:25 PM
Post #1 of 6
(3733 views)
|
|
B2000 won't start
|
Sign In
|
|
1987 Mazda B2000 5 spd.
The truck blew an old radiator hose on the freeway. When I got off I let it stop steeming and waited 20min. or so, filled it back up with water and drove it home. I put on new hoses filled it up and ran it for a wile and found another leak in a small hose under the intake manifold and a few pin holes in the radiator. I replaced the hose removed the radiator and had it fixed and cleaned. I put it all back together and now it won't start. It almost fires but wont start. It gets spark at all 4 plugs. the timing looks good, there is fuel in the tank and fuel comes out of the excelerator pump. There is also a "EGR" light on that wasn't there before.
Ideas?
jh
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Sep 22, 2009, 2:31 AM
Post #2 of 6
(3729 views)
|
|
Re: B2000 won't start
|
Sign In
|
|
Your going to have to remove the spark plugs and pressure test the cooling system. You likely got it hot enough to blow a head gasket and you are getting coolant into the cylinders now. A compression test may be helpful also.
If you had that many different leaks at once, then you have been neglecting the system for a while. I'm not sure what you did to "repair" the radiator but today's radiators are pretty much unrepairable.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
jh
New User
Sep 22, 2009, 5:10 AM
Post #3 of 6
(3720 views)
|
|
Re: B2000 won't start
|
Sign In
|
|
The radiator was removed and taken to a shop, cleaned flow tested and a few pin holes that were on a tank seam repaired. Is the pressure test on the coolant system easly done?
Thanks
jh
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Sep 22, 2009, 5:23 AM
Post #4 of 6
(3716 views)
|
|
Re: B2000 won't start
|
Sign In
|
|
Yes, you just simply attach it to the filler and pump it up, watching for pressure drop.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
jh
New User
Sep 22, 2009, 12:51 PM
Post #5 of 6
(3704 views)
|
|
Re: B2000 won't start
|
Sign In
|
|
Any ideas on the EGR light?
jh
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Sep 22, 2009, 12:59 PM
Post #6 of 6
(3701 views)
|
|
Re: B2000 won't start
|
Sign In
|
|
That's a maintenance reminder that goes on at 60,000 mikes to tell you to replace the EGR and O/2 sensor and reset the timing. There is a connector under the dash that has to be disconnected to reset the light.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
(This post was edited by Hammer Time on Sep 22, 2009, 1:04 PM)
|
|
| |
|
Auto Repair Home
SEARCH
WHO'S 
LOG 
1989 toyota pickup 3.0 crank no start
Please Help - Knock sound & engine fail
