|
|
ecogenie
New User
Feb 6, 2013, 3:22 PM
Post #1 of 7
(1189 views)
|
|
Not Starting After Ran
|
Sign In
|
|
1994 Chevy Blazer 4.3 Vlortec 4x4. I run the truck up and down the road. I turn it off and can not start it up again until it sits for some time. What could this be? Someone said a relay but don't know what relay. Anyone have any answers to this crazy mess I find myself in? I am unemployed and need to get this going so I can try and find a job. Need to feed the family and without transportation or money I am up the creek without a paddle. The creek is drying up and need to do something fast before I can't get back. Thanks so much for any help! 
(This post was edited by ecogenie on Feb 6, 2013, 3:25 PM)
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Feb 6, 2013, 4:07 PM
Post #2 of 7
(1159 views)
|
|
Re: Not Starting After Ran
|
Sign In
|
|
All "crank, no start" conditions are approached in the same way. Every engine requires certain functions to be able to run. Some of these functions rely on specific components to work and some components are part of more than one function so it is important to see the whole picture to be able to conclude anything about what may have failed. Also, these functions can ONLY be tested during the failure. Any other time and they will simply test good because the problem isn't present at the moment.
If you approach this in any other way, you are merely guessing and that only serves to replace unnecessary parts and wastes money.
Every engine requires spark, fuel and compression to run. That's what we have to look for.
These are the basics that need to be tested and will give us the info required to isolate a cause.
1) Test for spark at the plug end of the wire using a spark tester. If none found, check for power supply on the + terminal of the coil with the key on.
2) Test for injector pulse using a small bulb called a noid light. If none found, check for power supply at one side of the injector with the key on. (This is difficult with a Vortec so cave it for last)
3) Use a fuel pressure gauge to test for correct fuel pressure, also noticing if the pressure holds when key is shut off.
Once you have determined which of these functions has dropped out,
you will know which system is having the problem.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
ecogenie
New User
Feb 6, 2013, 5:15 PM
Post #3 of 7
(1146 views)
|
|
Re: Not Starting After Ran
|
Sign In
|
|
All "crank, no start" conditions are approached in the same way. Every engine requires certain functions to be able to run. Some of these functions rely on specific components to work and some components are part of more than one function so it is important to see the whole picture to be able to conclude anything about what may have failed. Also, these functions can ONLY be tested during the failure. Any other time and they will simply test good because the problem isn't present at the moment.
If you approach this in any other way, you are merely guessing and that only serves to replace unnecessary parts and wastes money.
Every engine requires spark, fuel and compression to run. That's what we have to look for.
These are the basics that need to be tested and will give us the info required to isolate a cause.
1) Test for spark at the plug end of the wire using a spark tester. If none found, check for power supply on the + terminal of the coil with the key on.
2) Test for injector pulse using a small bulb called a noid light. If none found, check for power supply at one side of the injector with the key on. (This is difficult with a Vortec so cave it for last)
3) Use a fuel pressure gauge to test for correct fuel pressure, also noticing if the pressure holds when key is shut off.
Once you have determined which of these functions has dropped out,
you will know which system is having the problem. Okay but it does start. The only time it doesn't start is right after it is turned off. I sits for a while and it starts right up with no problems. Only when it has ran it will not start. If it were the spark plug it would not start the first time.
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Feb 6, 2013, 5:17 PM
Post #4 of 7
(1140 views)
|
|
Re: Not Starting After Ran
|
Sign In
|
|
You have an intermittent failure. That's why it has to be tested only during that period that it won't start.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
ecogenie
New User
Feb 6, 2013, 5:28 PM
Post #5 of 7
(1131 views)
|
|
Re: Not Starting After Ran
|
Sign In
|
|
Okay I will try it out. Do all the plugs need to be checked or just until I notice one not good?
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Feb 6, 2013, 5:32 PM
Post #6 of 7
(1125 views)
|
|
Re: Not Starting After Ran
|
Sign In
|
|
You only need to check for spark at one cylinder at the time it won't start. The way we do this is we hook up our spark tester and fuel pressure gauge ahead of time. Then we just keep trying the car until it fail and observe if we still have spark and correct fuel pressure. What happens with those 2 functions will determine if you have to test injector pulse also.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
Auto Repair Home
SEARCH
WHO'S 
LOG 
1989 toyota pickup 3.0 crank no start
Please Help - Knock sound & engine fail
