|
|
tes
User
Dec 23, 2012, 5:53 PM
Post #1 of 14
(1633 views)
|
Hi there 2000 Mitsubishi the engine stall when the car stops at the traffic light don't know the cause, need your advice.
|
|
| |
|
Discretesignals
Ultimate Carjunky
/ Moderator
Dec 23, 2012, 6:12 PM
Post #2 of 14
(1620 views)
|
Model and engine size? Automatic or manual? Check engine light on? Since we volunteer our time and knowledge, we ask for you to please follow up when a problem is resolved.
|
|
| |
|
tes
User
Dec 24, 2012, 9:06 AM
Post #3 of 14
(1557 views)
|
Hi there thank you, yes there is a code p0113 intake air temperature high, is this the mass air flow sensor. and it is automatic trani engine is 2.7 mary-x-mass and thank you for the help.
|
|
| |
|
Discretesignals
Ultimate Carjunky
/ Moderator
Dec 24, 2012, 9:25 AM
Post #4 of 14
(1550 views)
|
2.7L? Mits doesn't offer that size engine in their line up for that year on any of their models in the USA. Still need to know what model yours is. Since we volunteer our time and knowledge, we ask for you to please follow up when a problem is resolved.
|
|
| |
|
tes
User
Dec 25, 2012, 12:19 PM
Post #5 of 14
(1503 views)
|
Hi there happy holidays, sorry for mess the car is 4 cylinder and it is 2.0 engine.
|
|
| |
|
nickwarner
Veteran
/ Moderator
Dec 25, 2012, 1:26 PM
Post #6 of 14
(1496 views)
|
OBD-II Trouble Code Technical Description Intake Air Temperature Circuit High Input What does that mean? The powertrain control module (PCM) monitors the temperature of the air entering the engine. The PCM supplies a 5 voltreference voltage to the Intake Air Temperature (IAT) sensor. The IAT is a thermistor that varies resistance based on temperature. As the temperature increases, resistance decreases. Low temperature results in a high signal voltage. When the PCM sees a signal voltage higher than 5 volts, it sets this P0113 check engine light code. Potential Symptoms There will likely be no symptoms other than illumination of the Malfunction Indicator Lamp (MIL - Check Engine Light / Service Engine Soon). Causes A code P0113 may mean that one or more of the following has happened: Internally failed IAT sensor Faulty connection at IAT sensor Open in IAT ground circuit or signal circuit Short to voltage in IAT signal circuit or reference circuit IAT harness and/or wiring routed too close to high-voltage wiring (e.g. alternator, spark plug cables, etc.) Faulty PCM (less likely but not impossible) Possible Solutions First, if you have access to a scan tool, is there an IAT reading? If the IAT reading is logical then the problem is likely intermittent. If the reading is less than -30 degrees, unplug the connector. Install a jumper wire between the harness connector signal and ground circuits. The IAT temperature reading on the scan tool should be maxed out at the high end. For example it should be 280 degrees Farenheit or higher. If it is, the wiring is okay, and it may have been the connection. If it isn't install the jumper wire between the IAT signal circuit and the chassis ground. If now the IAT reading on the scan tool is maxed out then check for an open in the IAT ground circuit. If you get no reading at all on the scan tool, it's likely that the sensor signal is open or the 5 volt reference is missing. Check using a DVOM (digital volt ohm meter) for a 5 volt reference. If it's there, then unplug the connector at the PCM and check for continuity on the IAT signal circuit between the PCM connector and the IAT connector.
|
|
| |
|
tes
User
Dec 25, 2012, 3:10 PM
Post #7 of 14
(1488 views)
|
thank you for the help, do you know the location of that sensor, perhaps how it looks like too, can you send me the picture of the sensor. thank you again.
|
|
| |
|
Hammer Time
Ultimate Carjunky
/ Moderator
Dec 25, 2012, 4:22 PM
Post #8 of 14
(1483 views)
|
I guess you just don't want to tell anybody what model your car is? ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
tes
User
Dec 26, 2012, 10:47 AM
Post #9 of 14
(1452 views)
|
Hi there sorry I will do my best to communicate about cars in the wright way. here is the car's information year 2001 Mitisubushi eclipes GS 4 clynder 2.0 engine
|
|
| |
|
Hammer Time
Ultimate Carjunky
/ Moderator
Dec 26, 2012, 10:50 AM
Post #10 of 14
(1446 views)
|
According to my database, the 2.0 wasn't available in the 01 GS. I also see that the year changed half way through. Got some more accurate info? ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
(This post was edited by Hammer Time on Dec 26, 2012, 10:53 AM)
|
|
| |
|
nickwarner
Veteran
/ Moderator
Dec 26, 2012, 2:22 PM
Post #11 of 14
(1431 views)
|
Look on the sticker in the driver's door jamb. There should be a build sticker. Post the build date and the 8th and 10th digits of the VIN please.
|
|
| |
|
tes
User
Dec 27, 2012, 11:53 AM
Post #12 of 14
(1402 views)
|
Hi there thank you for all the help, and sorry for miss information, the car is 2004 Mitsubishi out lander 2.4 engine, the code is p0113 is this different than mass air flow sensor,
|
|
| |
|
Hammer Time
Ultimate Carjunky
/ Moderator
Dec 27, 2012, 12:45 PM
Post #13 of 14
(1393 views)
|
Unbelievable. Now we went from a car to a truck. That code is for a problem with the intake air temp circuit. That is a very different circuit from the MAF but in this case that sensor is built into the MAF although having the code doesn't automatically mean a bad sensor. ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
tes
User
Dec 27, 2012, 12:58 PM
Post #14 of 14
(1387 views)
|
thank you very much after we clean the MAF with air flow sensor cleaner, the car is ok.
|
|
| |
|