|
|
|
1990 oldsmobile cutlass ciera 3.3
|
|
|
| |
|
|
BRAY71
New User
Feb 16, 2017, 5:32 PM
Post #1 of 11
(3017 views)
|
1990 oldsmobile cutlass ciera 3.3
|
Sign In
|
|
1990 Oldsmobile cutlass ciera with a v6 3.3 was stalling after five seconds of running. first i put a fuel regulator on because the vacuum line smelled like straight fuel. still did it then i replaced the mass air flow sensor because it was throwing a code 34 for it i checked the wire good power and ground. so with new mas sensor it will run but ruff an still stall sometimes when cold so i tested resistance on fuel injectors 3 tested bad so i replaced those an still no luck. then i replaced the idle air control valve an tested the wires. then with a new iac it still runs ruff an stalls sometimes. and it also has good fuel pressure as well so i am stumped and ideas?
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Feb 16, 2017, 6:12 PM
Post #2 of 11
(3010 views)
|
|
Re: 1990 oldsmobile cutlass ciera 3.3
|
Sign In
|
|
Have you taken a compression test to determine if the engine is mechanically sound?
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
BRAY71
New User
Feb 17, 2017, 6:43 AM
Post #3 of 11
(2981 views)
|
|
Re: 1990 oldsmobile cutlass ciera 3.3
|
Sign In
|
|
Yes compression is good
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Feb 17, 2017, 7:01 AM
Post #4 of 11
(2975 views)
|
|
Re: 1990 oldsmobile cutlass ciera 3.3
|
Sign In
|
|
Really? What were the readings?
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
BRAY71
New User
Feb 17, 2017, 7:03 AM
Post #5 of 11
(2971 views)
|
|
Re: 1990 oldsmobile cutlass ciera 3.3
|
Sign In
|
|
They were all reading between 101 an 105
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Feb 17, 2017, 7:09 AM
Post #6 of 11
(2969 views)
|
|
Re: 1990 oldsmobile cutlass ciera 3.3
|
Sign In
|
|
That really isn't that good.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
Tom Greenleaf
Ultimate Carjunky
/ Moderator
Feb 17, 2017, 7:24 AM
Post #7 of 11
(2965 views)
|
|
Re: 1990 oldsmobile cutlass ciera 3.3
|
Sign In
|
|
1990 and all that close! Doubt that. IMO that's not enough compression to fire normally if at all. If really done check that gauge with something known or you can also use a vacuum gauge in line while knowing your altitude to actual manifold vacuum while running and at raised RPM like 2,000 or so. Should be the same as idle if smooth enough at idle or exhaust restriction likely. If uniformly low valve timing suspect.
It's a 1990 so age alone means lots of things are possible but off to a bad start if compression is true at that,
T
|
|
| |
|
|
kev2
Veteran
Feb 17, 2017, 8:37 AM
Post #8 of 11
(2955 views)
|
|
Re: 1990 oldsmobile cutlass ciera 3.3
|
Sign In
|
|
install fuel pressure gauge, record reading KOEO - start engine observe pressure - what is PSI as it shuts down in that @5sec? Post numbers.
post ALL the codes you have at present time.
|
|
| |
|
|
Discretesignals
Ultimate Carjunky
/ Moderator
Feb 17, 2017, 9:45 AM
Post #9 of 11
(2945 views)
|
|
Re: 1990 oldsmobile cutlass ciera 3.3
|
Sign In
|
|
100 psi is horrible and would be the bare minimum spec. All the plugs were removed, the battery was fully charged, and the throttle was wide open during your testing?
If you put some oil in the cylinder, what happens to the compression pressure? No wonder the MAF is outputting a low grams/sec signal.
Since we volunteer our time and knowledge, we ask for you to please follow up when a problem is resolved.
(This post was edited by Discretesignals on Feb 17, 2017, 9:46 AM)
|
|
| |
|
|
BRAY71
New User
Feb 17, 2017, 11:12 AM
Post #10 of 11
(2932 views)
|
|
Re: 1990 oldsmobile cutlass ciera 3.3
|
Sign In
|
|
Has a 34 and a 44 the 34 is for maf an 44 I think is a lean code haven't get a chance to get back an check compression with oil will do here in a few hours
|
|
| |
|
|
Tom Greenleaf
Ultimate Carjunky
/ Moderator
Feb 17, 2017, 11:31 AM
Post #11 of 11
(2926 views)
|
|
Re: 1990 oldsmobile cutlass ciera 3.3
|
Sign In
|
|
Forget codes till engine is proven better than that as it's just throwing info randomly with bad info if correct or close to that low. Oil if rings/pistons worn would spike higher compression and if just a tad higher I say valve timing in question - at the timing chain.
Engine must crank at a normal RPM with throttle held wide open as said.
Just don't go too nuts with oil - the rule is you use a squirt so don't put too much in. You count 4th pulse as the final results while cranking. It's said to do all this with warm engine which is very hard to have ALL plugs out in time to do that,
T
|
|
| |
|
Auto Repair Home
SEARCH
WHO'S 
LOG 
1989 toyota pickup 3.0 crank no start
Please Help - Knock sound & engine fail
