|
|
|
1994 E150 new tie rod issue
|
|
|
| |
|
|
gooch mango
Novice
Mar 24, 2012, 11:56 AM
Post #1 of 9
(2175 views)
|
|
1994 E150 new tie rod issue
|
Sign In
|
|
I replaced the tie rod ends and center link (aka right inner tie rod end) on my 1994 Ford E150... a relatively simple job. It went well except for one kinda important thing -- I cannot get the retainer nut joining the left inner tie rod to the center link to tighten to torque specs (75 ft. lbs.). It tightened to about 20 ft. lbs. (a rough guess), and then the threaded post began turning, and the retaining nut can no longer get any tighter.  (It is on there far enough to get the cotter pin in.)
My question: Is it possible to pop off the back of the tie rod end (where the zerk fitting is) and put a wrench on the post, or will that just ruin the brand new tie rod?
|
|
| |
|
|
Discretesignals
Ultimate Carjunky
/ Moderator
Mar 24, 2012, 12:04 PM
Post #2 of 9
(2169 views)
|
|
Re: 1994 E150 new tie rod issue
|
Sign In
|
|
So the joint is spinning when you go to tighten the nut? If that is the case one trick that I use is taking a large set of channel locks and squeezing the joint into the center link. The pressure should cause the joint to grip the hole it slides through, so you can tighten the nut without it spinning.
There might be other tricks and if there are I am interested in reading about them.
Since we volunteer our time and knowledge, we ask for you to please follow up when a problem is resolved.
(This post was edited by Discretesignals on Mar 24, 2012, 12:06 PM)
|
|
| |
|
|
gooch mango
Novice
Mar 24, 2012, 2:19 PM
Post #3 of 9
(2137 views)
|
|
Re: 1994 E150 new tie rod issue
|
Sign In
|
|
Hmmm... I think the post thing is tapered, so that just might work. And it'll be a heck of a lot easier than tearing open the backside of the joint. Thanks! I'll try that in the morning. 
|
|
| |
|
|
nickwarner
Veteran
/ Moderator
Mar 24, 2012, 8:29 PM
Post #4 of 9
(2113 views)
|
|
Re: 1994 E150 new tie rod issue
|
Sign In
|
|
What I do on these, especially ones with difficulty to grip the bottom, is to pop it apart and take a center punch in your hole and on the taper of the joint. Peening it with the center punch gives it some grip and when you put it in its 99% effective to hold without spinning while you tighten it.
|
|
| |
|
|
gooch mango
Novice
Mar 25, 2012, 7:20 AM
Post #8 of 9
(2091 views)
|
|
Re: 1994 E150 new tie rod issue
|
Sign In
|
|
And it'll be a heck of a lot easier than tearing open the backside of the joint. Huh?
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Mar 25, 2012, 7:24 AM
Post #9 of 9
(2087 views)
|
|
Re: 1994 E150 new tie rod issue
|
Sign In
|
|
Be thankful you didn't try that.
There is nothing inside there but the round, ball base that rotates in the encased housing that you were about to destroy.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
Auto Repair Home
SEARCH
WHO'S 
LOG 
1989 toyota pickup 3.0 crank no start
Please Help - Knock sound & engine fail
