|
|
|
92 gmc vandura brake warning light cause
|
|
|
| |
|
|
dalesvandura
User
Jun 12, 2010, 9:08 PM
Post #1 of 21
(10109 views)
|
92 gmc vandura brake warning light cause
|
|
|
i have a 92 gmc vandura 2500 with the 5.7 and i have a brake warning light that wont go off on the dash i have checked my fluid levels they are fine i recently replaced my rotors pads and calipers bled them and the rear lines just make sure my mechanic didnt screw up i also have all new lines except for the ones from my master cylinder to the proportioning valve i would love any help i can get im willing to try just about any thing also i got a new battery had the people at the parts store install it and they knocked off and managed to unplug a black box that was mounted to upper section of the corner panel near the bulkhead
|
|
| |
|
|
nickwarner
Veteran
/ Moderator
Jun 12, 2010, 11:45 PM
Post #2 of 21
(10104 views)
|
|
Re: 92 gmc vandura brake warning light cause
|
|
|
two things come to mind, each as likely as the other. Either your master cylinder has a plastic reservoir and a plug in for a low fluid level sensor which is bad, or your e-brake pedal is slightly applied. Pull the e-brake release with one hand while pulling up one the pedal with the other and see if the light goes off. If so, you have found the gremlin. Otherwise, unplug the electrical connector at the master and see if the light goes off. If so, and the level of fluid in the master is within spec, its the sensor you unplugged at fault. This is assuming that all 4 brakes are functioning as they should of course.
|
|
| |
|
|
dalesvandura
User
Jun 13, 2010, 1:16 AM
Post #3 of 21
(10101 views)
|
|
Re: 92 gmc vandura brake warning light cause
|
|
|
park break is fine that was the first thing i checked seeing as how i do occasionally use it and no there is no plug on the master cylinder or on the plastic tanks there is one on the proportioning valve that does not change the status of light whether it is plugged in or not it also feels like only my front brakes are working despite all the rear brake componets checking out ok no leaks in the wheel cylinders and no unacceptable wear on the shoes and drums though when i bled the rears brakes i did not get the usual blast of brake fluid it was much more of a trickle
(This post was edited by dalesvandura on Jun 13, 2010, 1:38 AM)
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Jun 13, 2010, 4:49 AM
Post #4 of 21
(10095 views)
|
|
Re: 92 gmc vandura brake warning light cause
|
|
|
Take a large screwdriver and rap the side of the master cylinder reservoir with the handle a few times and see if the light goes off. It's very common for the float to stick at the bottom of the reservoir when it went dry during the repair and the flotation isn't enough to dislodge it from the gunk.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
(This post was edited by Hammer Time on Jun 13, 2010, 4:50 AM)
|
|
| |
|
|
dalesvandura
User
Jun 13, 2010, 8:17 AM
Post #5 of 21
(10087 views)
|
|
Re: 92 gmc vandura brake warning light cause
|
|
|
there is no float and it was just fine for a while other than not having rear brakes the lines from the master were plugged and the resovoir didnt go empty any idea what the little black box i described is that got disconnected and then put back in same time and thats about when this problem started but it also makes it feel like i now have rear brakes
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Jun 13, 2010, 8:52 AM
Post #6 of 21
(10083 views)
|
|
Re: 92 gmc vandura brake warning light cause
|
|
|
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
dalesvandura
User
Jun 13, 2010, 1:17 PM
Post #7 of 21
(10074 views)
|
|
Re: 92 gmc vandura brake warning light cause
|
|
|
hey this is pretty helpful except that one i dont have antilock breaks 2 i already tried the park brake check and disconnect of the switch and 3 the locations of the components to check are not listed like that in a haynes manual and i cant afford all data at the moment if you could post the diagram with the locations and numbers it would be a big help but other than that is there anything else that could cause this kind of a problem
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Jun 13, 2010, 1:20 PM
Post #8 of 21
(10072 views)
|
|
Re: 92 gmc vandura brake warning light cause
|
|
|
I have given you the factory diagnostic procedure for your problem. If you can't figure it out from that, head to the shop.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
dalesvandura
User
Jun 13, 2010, 1:29 PM
Post #9 of 21
(10066 views)
|
|
Re: 92 gmc vandura brake warning light cause
|
|
|
see heres why i am doing it myself the dealer said they wont touch it my mechanic cant figure it out and im hoping some one else can give me some other thoughts on the matter and maybe think of something that got missed
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Jun 13, 2010, 1:32 PM
Post #10 of 21
(10063 views)
|
|
Re: 92 gmc vandura brake warning light cause
|
|
|
I have given you a procedure that systematically eliminates all possible causes. If your unable to follow them, then you need to let someone else do it.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
dalesvandura
User
Jun 13, 2010, 2:38 PM
Post #11 of 21
(10057 views)
|
Re: 92 gmc vandura brake warning light cause
|
|
|
so your telling me im an idiot thanks i went to matc for diesel powertain servicing and have had to do ellectrical on damn near everthing fom cars and trucks to boats small planes hobby stuff even appliances and have not once failed i know what im doing but the information you have given me was not accurate i have no sensors in the back of the van any where around the brake system the only thing plugged in is the single wire plug on the proportioning valve which is mounted on the drivers side front frame rail and the park brake switch thats it if you want pictures il send them
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Jun 13, 2010, 2:41 PM
Post #12 of 21
(10052 views)
|
|
Re: 92 gmc vandura brake warning light cause
|
|
|
So, did you unplug both of those switches as the test instructed?
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
dalesvandura
User
Jun 13, 2010, 2:58 PM
Post #13 of 21
(10046 views)
|
|
Re: 92 gmc vandura brake warning light cause
|
|
|
c 163 so long as thats the single plug on the propotioning valve then yes i unplugged both as the diagnostic flow chart instructed and still nothing the light remained on hence my frustration its the only vehicle i have and i cant afford to take it back to the shop for a third time i know its a long shot to ask but no one has answered me about the little black box that is mounted above the battery that had been disconnected could that maybe have something to do with it something like a secondary computer for the braking system that got screwed up and would some pictures help so you can see what im seeing and talking about
|
|
| |
|
|
dalesvandura
User
Jun 13, 2010, 3:04 PM
Post #14 of 21
(10042 views)
|
|
Re: 92 gmc vandura brake warning light cause
|
|
|
so i unplugged said mysterious black box and the brake warning light went off and my brakes still function any ideas cause now im really confused
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Jun 13, 2010, 3:04 PM
Post #15 of 21
(10041 views)
|
|
Re: 92 gmc vandura brake warning light cause
|
|
|
Are you talking about a flat module mounted vertically?
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Jun 13, 2010, 3:10 PM
Post #16 of 21
(10037 views)
|
|
Re: 92 gmc vandura brake warning light cause
|
|
|
That is the ABS module you said your truck didn't have. Your truck has rear wheel only ABS and it's storing a code. That's why your light is on.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
dalesvandura
User
Jun 13, 2010, 3:16 PM
Post #17 of 21
(10031 views)
|
|
Re: 92 gmc vandura brake warning light cause
|
|
|
not mounted vertical horizontal and its about 4 in wide 7 in long and about 3/4 in thick and if this is the problem how would i go about retrieving said code and or deleting it all toghether and how does rear wheel only abs work cause im used to seeing the big ugly block that controls the pressure and pulses it but where is that on my van i have now should i use flash diagnostics or pull out my obd 1 scanner
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Jun 13, 2010, 3:26 PM
Post #18 of 21
(10029 views)
|
|
Re: 92 gmc vandura brake warning light cause
|
|
|
Trouble codes can be accessed by connecting a TECH 1 scan tool or by manually grounding the ALDL connector. To manually ground the ALDL connector, connect a jumper wire between terminals A and H and observe the flashes of the brake warning lamp. Note the following when performing the Diagnostic Circuit Check to access trouble codes.
- When the terminals are jumped, count the number of short flashes starting from the initial long flash and including the long flash in the count.
- The count sequence will repeat as long as the ALDL connector terminals are jumped with the ignition on.
- Sometimes the first count sequence will be short. However, subsequent counts will be accurate.
- If more than one failure has occurred, only the first recognized failure code will be stored and flashed by the ECU.
- After determining the stored failure code, perform steps indicated by the diagnostic circuit check and follow the indicated failure code chart. After performing all indicated repairs, road test vehicle to check system operation, then recheck system for stored trouble codes.
This picture is for a Blazer but it shows the module
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Jun 13, 2010, 3:35 PM
Post #19 of 21
(10026 views)
|
|
Re: 92 gmc vandura brake warning light cause
|
|
|
These codes are for a 93 but they should be the same. It's the same system
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
cmvdvg
New User
Sep 15, 2013, 1:10 PM
Post #20 of 21
(8517 views)
|
|
Re: 92 gmc vandura brake warning light cause
|
|
|
My 91 vandura has same light on but it does go off after a while I'm thinking there is a burr on emergency brake cable inside drum and its sticking. Its self adjusting rear brakes so the self adjusting mechanism (it looks like a star or a spur from a boot) is sticking or cable itself but let me know if u fix it and what the problem is
|
|
| |
|
|
Tom Greenleaf
Ultimate Carjunky
/ Moderator
Sep 15, 2013, 1:23 PM
Post #21 of 21
(8514 views)
|
|
Re: 92 gmc vandura brake warning light cause
|
|
|
Please start you own thread with your own specifics. This one is now old and done. Locked now to keep it from this...........
T
|
|
| |
|
Auto Repair Home
SEARCH
WHO'S 
LOG 
1989 toyota pickup 3.0 crank no start
Please Help - Knock sound & engine fail
