Main IndexAuto Repair Home Search Posts SEARCH
POSTS 		Who's Online WHO'S
ONLINE 		Log in LOG
IN




Automotive Repair
Car Troubleshooting Topics
  Car Troubleshooting
  Engine Troubleshooting
  Engine Fault Codes
  Electrical and Wiring
  Transmission Problems

Car Repair Topics
  Car Making Noises
  Car Stereo Repair
  Heating or AC Issues
  Motorcycles and ATVs
  Tricks of the Trade
  Truck Repair Advice

Site Options:   
  Login
  Sign up here!



Latest Forum Post
with_replies.gif image   1989 toyota pickup 3.0 crank no start
I have a 1989 toyota pickup 3.0 crank no...

with_replies.gif image   Strut spring orientation and strut mount tension nut
2017 Nissan rogue awd 2.5 L Put in Monro...

with_replies.gif image   Transmission stuck in part, I have tried everything
So I'm working on my elderly fathers 201...

with_replies.gif image   2017 dodge journey LED headlights on/off randomly
Year of vehicle 2017 Make of vehicle dod...

with_replies.gif image   Kia Soul starter replacement issues!
Okay so my car is a 2010 Kia soul 2.0 en...

hot_with_replies.gif image   Please Help - Knock sound & engine fail
Hi all, Hoping to get some insight and ...

with_replies.gif image   multiple warning lights
2013 GMC Terrain 130,000 miles 4 cylinde...

with_replies.gif image   03 alero no low speed blower
Good day everyone, I have a 2003 Olds a...

with_replies.gif image   04 Chevy 2500hd tail light issues
Help!!! I have changed my combo switch...

with_replies.gif image   1999 Grand Caravan Sport not starting.
Hi. I'm new here. I hope someone can hel...




bad idle and blow by

Search for (search options)
 



daveyoski
New User

Dec 18, 2012, 6:14 PM

Post #1 of 5 (2148 views)
post icon bad idle and blow by Sign In
I have a 1986 olds. cutlass ceira and I have replaced plugs, wires, and cap and still the car run ruff also a lot of oil blow by into my air case. There is no water in the oil and no water coming out of the tail pipe. but it overheats after idling for 2 min. Can someone help me with this ? I dont feel that the head is bad but not sure. Thankshttp://www7.carjunky.com/images/arg.gif


MarineGrunt
Enthusiast
MarineGrunt profile image

Dec 18, 2012, 9:42 PM

Post #2 of 5 (2094 views)
Re: bad idle and blow by Sign In
There doesn't have to be water (I assume you mean coolant) coming out of the exhaust for it to be a head gasket. The coolant would more likely be burned off before it exits anyways. But, just because it's overheating doesn't mean it's a head gasket either. It could be as simple as a stuck thermostat. How's your coolant level? What you need to do is pressure test the cooling system and check for leaks.

There are a handful of professional mechanics on this site that will be able to give you much better advice than I can so be sure to check back.


nickwarner
Veteran / Moderator
nickwarner profile image

Dec 19, 2012, 3:03 PM

Post #3 of 5 (2065 views)
Re: bad idle and blow by Sign In
Have you checked the water pump to be sure its still working properly? If you have a lot of blowby, have you checked or replaced the PCV valve? Have you done a compression test?


ron79
Novice

Jan 8, 2013, 6:14 PM

Post #4 of 5 (1981 views)
Re: bad idle and blow by Sign In
Rough idle could be from alot of things as your car is a 86.
But i would start with the idle air control vale, clean the Throttle body and clean the egr vale.(May need new gasket)
Does your car have engine light on?
You say you replaced wires, plugs and dist cap is that it or was it a full tune up including dist rotor, air filter, fuel filter, PCV, Thermostat and so on?
Does your car run on OBD2 emissions system or older charcoal canister type.
Purge vale for evap system can cause issues if not working.


nickwarner
Veteran / Moderator
nickwarner profile image

Jan 8, 2013, 7:48 PM

Post #5 of 5 (1967 views)
Re: bad idle and blow by Sign In
In Reply To
Rough idle could be from alot of things as your car is a 86.

Does your car run on OBD2 emissions system or older charcoal canister type.
Ron, really? Honestly if you have to ask if he has OBDII on a vehicle that was made a full decade before OBDII came out you should stick to the welding and not the diagnostics. We welcome people to give help to others here, but it needs to be help based on knowledge, facts and evidence not just throwing out random names of stuff and guesswork. No EVAP system is going to create blowby. No EVAP system is going to create idle problems.

Please limit your advice to things you have had firsthand experience with to give advice on.





 
 
 






Search for (options) Privacy Sitemap