Press in Bearing - Steering and Suspension


	Auto Repair Home	SEARCH POSTS	WHO'S ONLINE	LOG IN

Automotive Repair

Car Troubleshooting Topics
  Car Troubleshooting
  Engine Troubleshooting
  Engine Fault Codes
  Electrical and Wiring
  Transmission Problems

Car Repair Topics
  Car Making Noises
  Car Stereo Repair
  Heating or AC Issues
  Motorcycles and ATVs
  Tricks of the Trade
  Truck Repair Advice

Site Options:
  Login
  Sign up here!

Latest Forum Post

Lukewarm Heat............

New antifreeze reverse flush heater core...

multiple warning lights

2013 GMC Terrain 130,000 miles 4 cylinde...

2014 Nissan Sentra Shaking

Car recently started shaking when accele...

Buy Flualprazolam Powder Online Whatsapp: +1(424) 328-1086

N/A

1989 toyota pickup 3.0 crank no start

I have a 1989 toyota pickup 3.0 crank no...

Strut spring orientation and strut mount tension nut

2017 Nissan rogue awd 2.5 L Put in Monro...

Transmission stuck in part, I have tried everything

So I'm working on my elderly fathers 201...

2017 dodge journey LED headlights on/off randomly

Year of vehicle 2017 Make of vehicle dod...

Kia Soul starter replacement issues!

Okay so my car is a 2010 Kia soul 2.0 en...

Please Help - Knock sound & engine fail

Hi all, Hoping to get some insight and ...

Press in Bearing

Sign up here!

Search for (search options)

Auto Repair Home>> Automotive Repair>> Steering and Suspension

MDWhite
User

Jun 22, 2016, 3:29 PM

Post #1 of 5 (1535 views)

Press in Bearing	Sign In

Doing a front wheel bearing on a 2004 Hyundai Accent. I am wondering how I should press the new one into the knuckle. I assume I am to use only the outer race but since they put the seal in the outer race you only have a ring abt 2mm in width at the outer edge to work with. My press kit has one driver just barely too big for the job and the next size down doesn't get much of the work area and I am afraid of damaging the seal if I use it. What should I do?

Hammer Time
Ultimate Carjunky / Moderator
Hammer Time profile image

Jun 22, 2016, 4:02 PM

Post #2 of 5 (1530 views)

Re: Press in Bearing	Sign In

What I usually do is press the hub out first. The inside half of the race will remain on the hub. I then use a cut-off wheel to cut most of the way though that race without cutting into the hub and then use a chisel to either split it or drive it off the hub.

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.

MDWhite
User

Jun 22, 2016, 8:26 PM

Post #3 of 5 (1522 views)

Re: Press in Bearing	Sign In

Well that is all done now. I am just talking about. putting the new bearing in.

Hammer Time
Ultimate Carjunky / Moderator
Hammer Time profile image

Jun 23, 2016, 1:57 AM

Post #4 of 5 (1514 views)

Re: Press in Bearing	Sign In

Press it into the knuckle first and then pres the hub into it while supporting it on the inner race on the other side.

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.

MDWhite
User

Jun 24, 2016, 12:30 PM

Post #5 of 5 (1498 views)

Re: Press in Bearing	Sign In

I see now that the knuckle has two bore diameters and the one above the snap ring groove is very slightly larger and will fortunately accept that driver I thought was too big for the job. That driver contacts the full outer ring of the race and should be fine. And it looks like the bearing will bottom in the knuckle before the groove is passed so it will not run into any interference. I'll post again when it is done.

Search for (options) Privacy Sitemap