|
|
|
1994 gmc sonoma v6. clutch
|
|
|
| |
|
|
fer308qv
Novice
Dec 10, 2012, 3:40 AM
Post #1 of 20
(5150 views)
|
|
1994 gmc sonoma v6. clutch
|
Sign In
|
|
clutch engages with pedal near floor. cant use floor mats it is so low. worn clutch? I understand there is no adjustment for this.
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Dec 10, 2012, 4:06 AM
Post #2 of 20
(5117 views)
|
|
Re: 1994 gmc sonoma v6. clutch
|
Sign In
|
|
That's right. That's the way hydraulics work. It's always possible you have mechanical issues too but definitely not adjustable.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
fer308qv
Novice
Dec 10, 2012, 7:43 AM
Post #3 of 20
(5102 views)
|
|
Re: 1994 gmc sonoma v6. clutch
|
Sign In
|
|
low pedal = bad clutch? hi pedal = good clutch?
|
|
| |
|
|
Tom Greenleaf
Ultimate Carjunky
/ Moderator
Dec 10, 2012, 9:11 AM
Post #4 of 20
(5092 views)
|
|
Re: 1994 gmc sonoma v6. clutch
|
Sign In
|
|
Hydraulic clutch LINKAGE not the clutch itself. If it wont disengage it would be air in it that doesn't belong, faults with master clutch cylinder, slave cylinder or any parts involved.
Wrong fluid (an oil) would destroy those too with anything rubber but perhaps not instantly,
T
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Dec 10, 2012, 9:11 AM
Post #5 of 20
(5089 views)
|
|
Re: 1994 gmc sonoma v6. clutch
|
Sign In
|
|
No, the other way around unless something is not letting it disengage normally, not real likely.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
fer308qv
Novice
Dec 10, 2012, 9:17 AM
Post #6 of 20
(5078 views)
|
|
Re: 1994 gmc sonoma v6. clutch
|
Sign In
|
|
So I possibly have air in the system. Purging or bleeding may allow the disengaging point to come further away from the floor. If I understand.
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Dec 10, 2012, 9:20 AM
Post #7 of 20
(5075 views)
|
|
Re: 1994 gmc sonoma v6. clutch
|
Sign In
|
|
How much free play before you hit some resistance in the clutch pedal?
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
fer308qv
Novice
Dec 10, 2012, 9:22 AM
Post #8 of 20
(5070 views)
|
|
Re: 1994 gmc sonoma v6. clutch
|
Sign In
|
|
about an inch.........sloppy loose.....tried to address that, but there is nothing to adjust.
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Dec 10, 2012, 11:07 AM
Post #9 of 20
(5064 views)
|
|
Re: 1994 gmc sonoma v6. clutch
|
Sign In
|
|
If you have excessive free play at the top, that could indicate air in the system but you would have to figure out how it got in there and resolve that issue before bleeding it..
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
fer308qv
Novice
Dec 10, 2012, 1:39 PM
Post #10 of 20
(5051 views)
|
|
Re: 1994 gmc sonoma v6. clutch
|
Sign In
|
|
condition has existed since I have owned it ....about 9 years...........I am addressing it now because I want to replace the rubber flooring that now has torn from not being able to have floor mats. I will have the system bled I guess.....Will be a good start.
thanks!
|
|
| |
|
|
Tom Greenleaf
Ultimate Carjunky
/ Moderator
Dec 10, 2012, 4:55 PM
Post #11 of 20
(5032 views)
|
|
Re: 1994 gmc sonoma v6. clutch
|
Sign In
|
|
19 years old, you've owned it this way for NINE years like this! I'm lost - Is the floor bent? - T
|
|
| |
|
|
fer308qv
Novice
Dec 11, 2012, 3:21 AM
Post #12 of 20
(5013 views)
|
|
Re: 1994 gmc sonoma v6. clutch
|
Sign In
|
|
floor isnt bent , but the carpet is worn through........
its a work truck that i put around 3500 miles a year on ..this winter im giving it a little tlc.........was looking at other trucks , but for the money mine is still fine.
|
|
| |
|
|
Tom Greenleaf
Ultimate Carjunky
/ Moderator
Dec 11, 2012, 5:25 AM
Post #13 of 20
(5003 views)
|
|
Re: 1994 gmc sonoma v6. clutch
|
Sign In
|
|
Arggh! I've tried to find exact pictures of this layout in whole given that pics help. Being there would be and just might be necessary to know exactly why this is like this and could be like that for so long as I would have guessed a failure would have happened by how I am interpreting your situation.
Seems universal that this is not adjustable. That alone doesn't mean things are all fine or will behave fine with engagement and disengagement at the right spot in the travel of the pedal inside. It should have some "free-play" area at the top such that you could just push it with your finger and have some "nothing" room which is needed. I'm not sure our understanding of what you are describing and how we are interpreting just what it's doing and that happens. The web is fantastic but not like experience and actually seeing and touching things whatever they are.
Found that the fork that the slave cylinder seems to be a popular replacement item for this. Not sure how much of this part you can see if much at all but it's like this.......
The slave cylinder has a fixed rod that pushes on the lower left of that bar if you will with the dimple centering the pushrod of the slave which looks like this....
That pointed rod is at a set length so would not be adjustable as said. If there was no air, no fault in the hydraulics anywhere, not a bend pedal inside or floor somehow bent up in the travel area IMO there is a higher chance that this item or the fork has an issue. I'm plain not sure you can view it operating in this case.
Some of these set up the bleeding is VERY difficult to get right. So if in the life it needed to be bled it could still have air which IMO and experience would make the actual pressure to release, disengage clutch where it would also engage be lower to the floor. Air would highly likely be odd feeling at assorted temps or multiple pushes on clutch pedal may change it's spot where on pedal travel the show happens.
Trouble is to fully investigate this hands on you or a tech would first check that the pedal and pivot action inside was fine, might plug master cylinder with line removed to feel then a solid hard pedal, watch the action at the slave and just might have to remove the transmission to check it out more if it can't be seen or an inspection cover removed. That fork probably requires transmission removal if bent, worn somehow. If that and keeping this almost anyone would suggest doing a full clutch replacement job. If not a rusted mess it may not be that horrible to do labor/time wise.
I'm reading between the lines that you care about this truck enough to replace the rubber floor/carpet, have just said you don't put that many miles on it. Hey, having this vehicle is probably very useful. Being a GM truck especially there will be parts for it for ages including many common things that would be dealer only.
In short this isn't the way the clutch should behave. I/we can't know your abilities to rule everything out down to the last possible reason for this or if you really are willing to pay to take it apart down to the clutch or do that yourself. I didn't check but I wouldn't have it all apart and not put a new clutch job with parts generally not that costly as things go vs time to get there. By age alone if keeping it, it would be nice to know it was done but just a clutch job alone isn't necessarily going to change this problem so it needs to be checked while intact now IMO by you or a tech.
If nothing else I'll warn you that if there's a hole in the rubber flooring it will get moisture in there that will not dry out well and be another problem entirely to fix. Such is life,
T
|
|
| |
|
|
Discretesignals
Ultimate Carjunky
/ Moderator
Dec 11, 2012, 5:49 AM
Post #14 of 20
(4995 views)
|
|
Re: 1994 gmc sonoma v6. clutch
|
Sign In
|
|
If the pressure plate fingers are worn out or if they don't extend out far enough, you have low engagement also.
Since we volunteer our time and knowledge, we ask for you to please follow up when a problem is resolved.
(This post was edited by Discretesignals on Dec 11, 2012, 5:54 AM)
|
|
| |
|
|
fer308qv
Novice
Dec 11, 2012, 8:19 AM
Post #15 of 20
(4980 views)
|
|
Re: 1994 gmc sonoma v6. clutch
|
Sign In
|
|
Thank you all for the tips..........will investigate further.........one last question.......Is there an inspection cover that can be removed to inspect clutch plate?
Other GM vehicles do........I assume this does.
|
|
| |
|
|
Tom Greenleaf
Ultimate Carjunky
/ Moderator
Dec 11, 2012, 9:46 AM
Post #16 of 20
(4970 views)
|
|
Re: 1994 gmc sonoma v6. clutch
|
Sign In
|
|
Others may have some tricks to make a judgement on the clutch itself for wear - I don't know of anything very dependable except taking it apart then you see everything including how worn flywheel might be. If you just saw a mess of metal filings or like brake dust to excess would alarm me. You've driven it for 9 years and didn't mention having a new one yet does suggest you didn't drive it too improperly. Some people can eat up a clutch in no time or miles and some can get the whole possible life of a vehicle out of them.
Maybe I missed something over all the years but people would ask me how long one is going to last on a used vehicle or one they've owned and I can drive it, see that it grabs assertively, no strange noises and still can't say how long it will last or where in its life expectancy it is??
T
|
|
| |
|
|
fer308qv
Novice
Dec 12, 2012, 6:05 AM
Post #17 of 20
(4937 views)
|
|
Re: 1994 gmc sonoma v6. clutch
|
Sign In
|
|
I bought the truck with 145k on it. The truck had a new clutch prior to that. I am easy on the clutch having driven them all my driving life some 40 years......2 months a year I haul a heavy compressor . This stresses both the clutch and the brake pads. There has been recent clutch chatter occasionally, but no slipping what so ever.
|
|
| |
|
|
Tom Greenleaf
Ultimate Carjunky
/ Moderator
Dec 12, 2012, 12:09 PM
Post #18 of 20
(4921 views)
|
|
Re: 1994 gmc sonoma v6. clutch
|
Sign In
|
|
I believe you know how to treat a clutch to some degree. 40 years of thinking you know how means nothing. You spent all this time and ignored the issue proves you don't know how to use a clutch. Entire auto makers don't offer them because of this. You have no clue and ignored it.
Case closed,
T
|
|
| |
|
|
fer308qv
Novice
Dec 13, 2012, 1:11 PM
Post #19 of 20
(4880 views)
|
|
Re: 1994 gmc sonoma v6. clutch
|
Sign In
|
|
I have no idea what you meant in your last post Tom...............But thank you anyway for the technical information you provided.
|
|
| |
|
|
Tom Greenleaf
Ultimate Carjunky
/ Moderator
Dec 13, 2012, 2:02 PM
Post #20 of 20
(4875 views)
|
|
Re: 1994 gmc sonoma v6. clutch
|
Sign In
|
|
With all my respect - really. There's something not right in this whole tread. If this problem came to me in person it would be handled, fixed or explained. I can' do that.
Hey - #1 is we so called professionals volunteer our time 100%. This issue should be a cake walk for a tech actually there which so far the WWW can't do.
You've put up with is for all these years I don't know how to advise. This vehicle was near new when I retired - yup - that long ago. Aready beaten to death is this needs to be witnessed by a tech. For the life of me I can't suggest better than that. If you want to fix this yourself or not it needs YOU to part with some bucks for where to go,
Tom
|
|
| |
|
Auto Repair Home
SEARCH
WHO'S 
LOG 
Lukewarm Heat............
Buy Flualprazolam Powder Online Whatsapp: +1(424) 328-1086
1989 toyota pickup 3.0 crank no start
