|
|
JBANKS
User
May 16, 2009, 4:00 PM
Post #1 of 9
(1360 views)
|
|
1996 CHEV S-10 4WD
|
Sign In
|
|
CAN ANYONE HELP ME OUT WITH SOME TIPS / ADVICE ON REPLACING A CLUTCH IN MY 1996 CHEVY S-10? IT'S A FOUR WHEEL DRIVE WITH THE 4.3 ENGINE. IT ALSO HAS THAT RIDICULOUS INTERNAL SLAVE CYLINDER. JUST LIKE THE BUMS ON THE FREEWAY OFF RAMPS "ANYTHING HELPS"
JBANKS
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
May 16, 2009, 4:09 PM
Post #2 of 9
(1357 views)
|
|
Re: 1996 CHEV S-10 4WD
|
Sign In
|
|
Do you have any equipment like transmission jacks to do this with?
That transmission and transfer case is about 4 feet long and could weight 500 pounds. It's nothing to mess with if your not experienced and equipped to do it.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
JBANKS
User
May 16, 2009, 4:18 PM
Post #3 of 9
(1353 views)
|
|
Re: 1996 CHEV S-10 4WD
|
Sign In
|
|
YEP, I'VE GOT THE TOOLS I JUST LACK THE TALENT
JBANKS
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
May 16, 2009, 4:22 PM
Post #4 of 9
(1351 views)
|
|
Re: 1996 CHEV S-10 4WD
|
Sign In
|
|
I really don't recommend this. You can not only get hurt real bad but you can do damage to the transaxle and that will get real expensive.
.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
(This post was edited by Hammer Time on May 16, 2009, 4:23 PM)
|
|
| |
|
|
JBANKS
User
May 16, 2009, 4:42 PM
Post #5 of 9
(1346 views)
|
|
Re: 1996 CHEV S-10 4WD
|
Sign In
|
|
REALLY DON'T HAVE A CHOICE AT THIS TIME, SHOP QUOTES WERE OUTRAGEOUS. I HAVE A GOOD TRANNY JACK AND THE TRUCK IS WELL SUPPORTED (A LITTLE OVERKILL I MIGHT ADD) I WAS WONDERING IF THE TRANS WOULD DROP ENOUGH TO GET THE TOP BOLTS OUT AFTER I TOOK OFF THE TRANS SUPPORT, AND HOW IN THE #^@! DO YOU GET THAT LINE OFF OF THE SLAVE CYLINDER?
JBANKS
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
May 16, 2009, 4:47 PM
Post #6 of 9
(1344 views)
|
|
Re: 1996 CHEV S-10 4WD
|
Sign In
|
|
Yes, once you lower the back of the trans, it will give you a little more room but not much. The easiest way is with a very long extension and swivel socket over the top of the trans.
To disconnect the line, you'll see a plastic ring outside of the metal fitting. Push the ring toward the fitting and the plastic line will slide out. They are really hard to bleed after doing that.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
JBANKS
User
May 16, 2009, 4:55 PM
Post #7 of 9
(1341 views)
|
|
Re: 1996 CHEV S-10 4WD
|
Sign In
|
|
THANKS, HERE WE GO!! PARAMEDICS ARE ON SPEED DIAL, CHECK. LIFE INSURANCE, CHECK. STILL HATE CHEVYS, DOUBLE CHECK!! REALLY APPRECIATE THE HELP HAMMER, THANKS AGAIN.
JBANKS
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
May 16, 2009, 4:57 PM
Post #8 of 9
(1338 views)
|
|
Re: 1996 CHEV S-10 4WD
|
Sign In
|
|
Make real sure that trans is secured to the jack good so it can't roll off. The are not balanced and will roll to the side.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
JBANKS
User
May 19, 2009, 8:20 AM
Post #9 of 9
(1326 views)
|
|
Re: 1996 CHEV S-10 4WD
|
Sign In
|
|
OK LET'S ABANDON THAT PROJECT. ANYONE OUT THERE KNOW OF A GOOD, (BY GOOD I MEAN INEXPENSIVE) SHOP IN THE SEATTLE AREA WHERE I CAN GET THIS DONE?
JBANKS
|
|
| |
|
Auto Repair Home
SEARCH
WHO'S 
LOG 
1989 toyota pickup 3.0 crank no start
Please Help - Knock sound & engine fail
