|
|
|
2004 Honda Civic doesn't wanna go
|
|
|
| |
|
|
Schoolrocker4567@carjunky.com
Novice
Feb 13, 2016, 5:17 PM
Post #1 of 11
(1936 views)
|
|
2004 Honda Civic doesn't wanna go
|
Sign In
|
|
I was going down the noticed my lights were dimming and my stereo was going on and off. Car lost like all the power. Opened my hood to find my alternator mounting bolt and adjustment bolt broke so we replaced both. Got the car running and it's like it doesn't want to go in like D, have to put in in like D3 to first start out. So we figured the transmission is slipping g so we replaced it and it's still doing the same thing. We then DE used to take it to a local auto zone and have it tested. We noticed the temperature gauge doesn't work and it doesn't realize when you put it in D, D2, D3 but does in Neutral, reverse, and park. They tried two different testers. The first one said it could not communicate with the vehicle, and the second one said error.
|
|
| |
|
|
Discretesignals
Ultimate Carjunky
/ Moderator
Feb 13, 2016, 5:38 PM
Post #2 of 11
(1929 views)
|
|
Re: 2004 Honda Civic doesn't wanna go
|
Sign In
|
|
Good bet when the alternator bolt broke, the alternator lost its ground and fried parts of the PCM.
SOURCE:
Honda Service News August 2004
TITLE:
Engine Won't Start? Check for Loose Alternator Bolts
APPLIES TO:
2001-04 Civic
SERVICE TIP:
Got a 2001-04 Civic in your shop with any or all of these symptoms?
- The engine cranks but it won't start.
- The MIL comes on.
- The immobilizer indicator blinks while the engine cranks.
- The HDS can't communicate with the ECM/PCM.
Check for loose alternator bolts. If these bolts are loose for any reason such as the alternator was R&R'ed or an accessory A/C was installed on a DX model at the dealership, the alternator can overcharge and fry the ECM/PCM.
If the alternator bolts are loose, tighten them, and try restarting the engine. If the engine still won't start, then check the ECM/PCM connector for battery voltage and ground. If you're reading battery voltage and ground at the connector, then replace the ECM/PCM. Keep in mind, though, any ECM/PCM damage that's caused by loose alternator bolts from A/C installation or body repair isn't covered by warranty.
Since we volunteer our time and knowledge, we ask for you to please follow up when a problem is resolved.
(This post was edited by Discretesignals on Feb 13, 2016, 5:39 PM)
|
|
| |
|
|
Schoolrocker4567@carjunky.com
Novice
Feb 13, 2016, 5:44 PM
Post #3 of 11
(1924 views)
|
|
Re: 2004 Honda Civic doesn't wanna go
|
Sign In
|
|
That's what I was thinking. But the car does start. Before all this happened I could turn the key to start for like a second and it'd fire right up but now I have to hold it for like 5-10 seconds and it'll start but the engine like bounces and spits and sputters until it gets warmed up a little bit then it idles fine
|
|
| |
|
|
Discretesignals
Ultimate Carjunky
/ Moderator
Feb 13, 2016, 5:47 PM
Post #4 of 11
(1922 views)
|
|
Re: 2004 Honda Civic doesn't wanna go
|
Sign In
|
|
Notice it says, "with any or all of these symptoms?"
Since we volunteer our time and knowledge, we ask for you to please follow up when a problem is resolved.
|
|
| |
|
|
Schoolrocker4567@carjunky.com
Novice
Feb 13, 2016, 5:49 PM
Post #5 of 11
(1917 views)
|
|
Re: 2004 Honda Civic doesn't wanna go
|
Sign In
|
|
Thank you. We will test the ECM and see how everything goes. I will keep you informed on the process
|
|
| |
|
|
Schoolrocker4567@carjunky.com
Novice
Feb 21, 2016, 5:05 PM
Post #6 of 11
(1875 views)
|
|
Re: 2004 Honda Civic doesn't wanna go
|
Sign In
|
|
Replaced the ECM and the problem is still there. Any other suggestions?
|
|
| |
|
|
Discretesignals
Ultimate Carjunky
/ Moderator
Feb 22, 2016, 7:00 PM
Post #7 of 11
(1852 views)
|
|
Re: 2004 Honda Civic doesn't wanna go
|
Sign In
|
|
Are you still not able to communicate with the PCM using a code reader? The first thing you should have done was to see why your code readers were not able to communicate the PCM. That probably would have verified the TSB above if you isolated the communication failure to the PCM internals.
I believe if you were to replace the PCM on that vehicle is has to be programmed with the transponder key codes for the engine to start. Was that all done?
Since we volunteer our time and knowledge, we ask for you to please follow up when a problem is resolved.
(This post was edited by Discretesignals on Feb 22, 2016, 7:06 PM)
|
|
| |
|
|
Schoolrocker4567@carjunky.com
Novice
Feb 22, 2016, 7:01 PM
Post #8 of 11
(1848 views)
|
|
Re: 2004 Honda Civic doesn't wanna go
|
Sign In
|
|
Nope. It still comes up "No Link"
|
|
| |
|
|
Discretesignals
Ultimate Carjunky
/ Moderator
Feb 22, 2016, 7:09 PM
Post #9 of 11
(1847 views)
|
|
Re: 2004 Honda Civic doesn't wanna go
|
Sign In
|
|
When you turn the ignition on does the check engine light come on?
Since we volunteer our time and knowledge, we ask for you to please follow up when a problem is resolved.
|
|
| |
|
|
Schoolrocker4567@carjunky.com
Novice
Feb 22, 2016, 7:24 PM
Post #10 of 11
(1840 views)
|
|
Re: 2004 Honda Civic doesn't wanna go
|
Sign In
|
|
Yes but it's been on. And the car does start and everything
|
|
| |
|
|
Discretesignals
Ultimate Carjunky
/ Moderator
Feb 22, 2016, 8:11 PM
Post #11 of 11
(1839 views)
|
|
Re: 2004 Honda Civic doesn't wanna go
|
Sign In
|
|
Check fuse 9 (15 amp) in the under hood fuse block and make sure it is good. That fuse protects the power feed circuits for the data link connector and the gauge assembly. If it is good, check for power on the data link connector pin 16 (white/red wire). It should have battery voltage on there all the time.
Once you can get communications restored, maybe can see why the check engine light is on.
Since we volunteer our time and knowledge, we ask for you to please follow up when a problem is resolved.
|
|
| |
|
Auto Repair Home
SEARCH
WHO'S 
LOG 
1989 toyota pickup 3.0 crank no start
Strut spring orientation and strut mount tension nut
