|
|
chickenhouse
Enthusiast
May 18, 2009, 3:34 PM
Post #1 of 17
(4368 views)
|
Pulled out orig stuck engine and getting ready to uplift another that runs. Was an automatic engine- going into standard car. Have used the clutch input shaft to extract the pilot bearing and now wanting some "old fart" advice on any other things to look for before install. Clutch disc looke good & pressure plate is good enough that a scotchbrite will clean it up good. Timing gears look good etc. What am I missing?
|
|
| |
|
|
Loren Champlain Sr
Veteran
/ Moderator
May 18, 2009, 5:52 PM
Post #2 of 17
(4364 views)
|
Be sure to replace the pilot bearing/bushing. I'd recommend having the flywheel resurfaced. If you can afford it, I'd replace the disc and the pressure plate while you've got it torn down. Better to do it, now.
Loren
SW Washington
|
|
| |
|
|
Loren Champlain Sr
Veteran
/ Moderator
May 19, 2009, 1:22 PM
Post #4 of 17
(4351 views)
|
I think that there's only three or four of us here old enough to remember Corvairs. Radiator replacement was a b..ch.
Loren
SW Washington
|
|
| |
|
|
Loren Champlain Sr
Veteran
/ Moderator
May 19, 2009, 1:54 PM
Post #6 of 17
(4342 views)
|
Oh, and don't forget the 140hp 'SPYDERS'. LOL. (The Monza's were just a wimpy 110hp)
Loren
SW Washington
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
May 19, 2009, 2:45 PM
Post #7 of 17
(4339 views)
|
Yeah, twin carb pancakes
Of course I didn't want anything to do with them back then............LOL
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
chickenhouse
Enthusiast
May 19, 2009, 6:17 PM
Post #8 of 17
(4331 views)
|
O K old farts. I said that cause I turned 60 3 months ago which qualifies me. This is the wimpy 110 hp. weeny I know. This is not my goal for a classic as I just sold a 62 Nova rag. My dad bought my sis a 62 vair with powerglide. What a dog!. I have never pulled (dropped) one of these engines. Whatan experience! The crank is above the cam, the timing gear cover is also the bell housing! Go figger? I called O'Reilys for the timing gasket, they said they would call back. Told them the timing gasket is on the bellhousing. They never called back. Making my own from a Busch box. Ain't it fun?
|
|
| |
|
|
Tom Greenleaf
Ultimate Carjunky
/ Moderator
May 19, 2009, 7:52 PM
Post #9 of 17
(4329 views)
|
Welcome to the "old fart" club. You aren't that far off from some of us. NAPA can be a lot of help with some old car stuff, IMO,
T
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
May 20, 2009, 1:14 AM
Post #10 of 17
(4320 views)
|
OK, enough is enough.................LOL
This is the ad that showed up at the bottom of this thread
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
Tom Greenleaf
Ultimate Carjunky
/ Moderator
May 20, 2009, 3:12 AM
Post #11 of 17
(4315 views)
|
Hammer - ads at bottom pay for the site - some are contradictory to the site but rotate so you don't always see what I do or others. There will always be something to fix at this site
Low pay for bottom ads. Banners pay best and so far by skin of teeth we get by. Posted ads are a not allowed as you know,
T
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
May 20, 2009, 3:19 AM
Post #12 of 17
(4310 views)
|
Tom relax, it just was posted for a laugh..............
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
Tom Greenleaf
Ultimate Carjunky
/ Moderator
May 20, 2009, 3:24 AM
Post #13 of 17
(4304 views)
|
Laugh! If I knew how to relax I wouldn't be making side bucks to use my butt cleavage for a nut cracker
T
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
May 20, 2009, 3:27 AM
Post #14 of 17
(4299 views)
|
LOL..........your too much
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
Loren Champlain Sr
Veteran
/ Moderator
May 20, 2009, 5:45 PM
Post #15 of 17
(4286 views)
|
>> use my butt cleavage for a nut cracker << Hmmmmm. I used to know a girl that could do that. Maybe, the one in the ad?
Loren
SW Washington
|
|
| |
|
|
Loren Champlain Sr
Veteran
/ Moderator
May 20, 2009, 5:49 PM
Post #16 of 17
(4285 views)
|
60? Okay, you are in! Coors Light boxes work quite well, too. Did the '62 have just a little lever mounted on the dash for the transmission? No park, of course. Can't remember, for sure.
Loren
SW Washington
|
|
| |
|
|
chickenhouse
Enthusiast
May 20, 2009, 6:57 PM
Post #17 of 17
(4280 views)
|
I'm not sure Loren, that car is not here. I got the whole undercarriage ( engine transaxle, front steering etc) and the body is sitting on the ground about 4 miles from me. I am supposed to pick it up & bring it home also. Good glass & other parts remain. The 60 we had DID have the little lever on the right side of the steering wheel on the dash. Powerglide, so they called it. Peanutbutter drive. WOOF! I'll need to get an ignition key for this one soon. Don't know what's in the trunk, no key for that either.
|
|
| |
|
Auto Repair Home
SEARCH
WHO'S 
LOG 
1989 toyota pickup 3.0 crank no start
Strut spring orientation and strut mount tension nut
