|
|
Guest
Anonymous Poster
bibblentomtom@yahoo.com
Aug 16, 2009, 1:53 PM
Post #1 of 8
(1982 views)
|
|
Differential question
|
Sign In
|
|
Can a GM 10 bolt non-posi c-clip differential carrier be replaced with a posi unit?
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Aug 16, 2009, 9:05 PM
Post #2 of 8
(1976 views)
|
|
Re: Differential question
|
Sign In
|
|
Sure it can. The problem you are going to encounter though will be the match up of the ring and pinion if you leave the old pinion or the proper setup if you replace that also. It requires a lot of measurement setup and special tools to do it properly.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
Guest
Anonymous Poster
bibblentomtom@yahoo.com
Aug 17, 2009, 12:48 PM
Post #3 of 8
(1968 views)
|
|
Re: Differential question
|
Sign In
|
|
Thank you Hammer Time!!! I plan to change the ring and pinion as well. I am aware of proper place ment of the pinion, so I will have it done by a pro. I just wanted to do some research first. Thank you again!! Tom Nalley
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Aug 17, 2009, 12:51 PM
Post #4 of 8
(1965 views)
|
|
Re: Differential question
|
Sign In
|
|
You could probably get away with no set up if you reuse the same ring and pinion and all the side shims and just replace the cluster. Transfer the ring gear to the posi cluster.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
Loren Champlain Sr
Veteran
/ Moderator
Aug 17, 2009, 1:33 PM
Post #5 of 8
(1960 views)
|
|
Re: Differential question
|
Sign In
|
|
This isn't a 4X4, right?
Loren
SW Washington
|
|
| |
|
|
Guest
Anonymous Poster
bibblentomtom@yahoo.com
Aug 17, 2009, 10:50 PM
Post #6 of 8
(1954 views)
|
|
Re: Differential question
|
Sign In
|
|
No, this is not for a 4X4. I am restoring a 67 Camaro. I am wanting to use the factory installed rear end.The factory diff. carrier was broken and removed. So, I have an empty rear end with nothing but axles. [mad]
|
|
| |
|
|
Loren Champlain Sr
Veteran
/ Moderator
Aug 18, 2009, 9:31 AM
Post #7 of 8
(1950 views)
|
|
Re: Differential question
|
Sign In
|
|
Sorry to butt in; Auburn makes a very good quality (and strong) carrier.
Loren
SW Washington
|
|
| |
|
|
Guest
Anonymous Poster
bibblentomtom@yahoo.com
Aug 18, 2009, 1:50 PM
Post #8 of 8
(1944 views)
|
|
Re: Differential question
|
Sign In
|
|
Your not butting in at all. I'll take all the info I can get. As far as Auburn, I have have seen that other people seem to like them as well. I have also checked on Eaton. not sure yet what I will go with, I have plenty of time to decide.
|
|
| |
|
Auto Repair Home
SEARCH
WHO'S 
LOG 
Lukewarm Heat............
Buy Flualprazolam Powder Online Whatsapp: +1(424) 328-1086
1989 toyota pickup 3.0 crank no start
