Engine Change - Truck Repair Advice


	Auto Repair Home	SEARCH POSTS	WHO'S ONLINE	LOG IN

Automotive Repair

Car Troubleshooting Topics
  Car Troubleshooting
  Engine Troubleshooting
  Engine Fault Codes
  Electrical and Wiring
  Transmission Problems

Car Repair Topics
  Car Making Noises
  Car Stereo Repair
  Heating or AC Issues
  Motorcycles and ATVs
  Tricks of the Trade
  Truck Repair Advice

Site Options:
  Login
  Sign up here!

Latest Forum Post

1989 toyota pickup 3.0 crank no start

I have a 1989 toyota pickup 3.0 crank no...

Strut spring orientation and strut mount tension nut

2017 Nissan rogue awd 2.5 L Put in Monro...

Transmission stuck in part, I have tried everything

So I'm working on my elderly fathers 201...

2017 dodge journey LED headlights on/off randomly

Year of vehicle 2017 Make of vehicle dod...

Kia Soul starter replacement issues!

Okay so my car is a 2010 Kia soul 2.0 en...

Please Help - Knock sound & engine fail

Hi all, Hoping to get some insight and ...

multiple warning lights

2013 GMC Terrain 130,000 miles 4 cylinde...

03 alero no low speed blower

Good day everyone, I have a 2003 Olds a...

04 Chevy 2500hd tail light issues

Help!!! I have changed my combo switch...

1999 Grand Caravan Sport not starting.

Hi. I'm new here. I hope someone can hel...

Engine Change

Sign up here!

Search for (search options)

Auto Repair Home>> Truck Repair>> Truck Repair Advice

crash741
New User

Jun 26, 2009, 2:46 AM

Post #1 of 4 (3242 views)

Engine Change	Sign In

I have a 1979 Chevy pickup in which I have changed motors. The new motor came out of a 74 chevy pickup. The 79 had electronic ignition but the 74 didn't. I was wondering are there wires that have to be eliminated with the change? The 79 wiring was kind of a mess and we are trying to figure it out. Thanks

Tom Greenleaf
Ultimate Carjunky / Moderator
Tom Greenleaf profile image

Jun 26, 2009, 4:23 AM

Post #2 of 4 (3238 views)

Re: Engine Change	Sign In

Right - 75 started HEI ingnitions. I'd try hard to keep it as there are just four wires that link to it and damn I don't know which is which - one plain power, one for tach and sources for others have to be simple ign and perhaps from a ballast resistor but not sure enabled just while starter is cranking. Hope someone here can tell you which does which better as HEI is the better dist even though old one worked fine too - just had to fool with points now and then,

T

Loren Champlain Sr
Veteran / Moderator
Loren Champlain Sr profile image

Jun 26, 2009, 8:46 AM

Post #3 of 4 (3230 views)

Re: Engine Change	Sign In

crash; First, I'd recommend using the HEI distributor that came out of the original engine. As Tom said, it is by far better than the old point type. And, the vehicle is already wired for it. If you must switch distributors and use the point type: 12V with ignition on goes to the + side of the conventional coil that you'll have to buy. The distributor will have one lead in wire which connects to the - side of the coil. You can use the large red wire from the OE harness that would have plugged into the coil for the 12V source as it should be already wired correctly (hot only when key is on). If you have a tachometer, the small brown wire with the female connector that plugged into the OE distributor cap can be connected to the - side of the coil.
Loren
SW Washington

chickenhouse
Enthusiast

Jun 26, 2009, 10:44 AM

Post #4 of 4 (3224 views)

Re: Engine Change	Sign In

Use the H E I system your truck is set up for by all means. Also use plugs designed for H E I. Different heat range I believe.

Search for (options) Privacy Sitemap